ProForm PFTL38581 Maintenance and TROUBLE-SHOOTING, Problem The power turns off during use, Top

Page 12

MAINTENANCE AND TROUBLE-SHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page 7.) Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the con- sole. (See step 1 on page 8.)

c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console. (See step 1 on page 8.)

d. If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Check the batteries in the console. See BATTERY INSTALLATION on page 8. Most problems are the result of drained batteries.

b. Remove the key from the console and UNPLUG THE

POWER CORD. Next, remove the screws from the hood and carefully remove the hood.Locate the Reed Switch (86) and the Magnet (87) on the left side of the Pulley (85). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap be- tween the Magnet and the Reed Switch is about 1/8Ó. If necessary, loosen the Screw (67) and move the Reed Switch slightly. Retighten the Screw. Re-at- tach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8Ó

85

86

 

 

87

67

 

Top

 

View

 

12

Image 12
Contents QUESTIONS? Model No. PFTL38581 Serial NoCustomer HOT Line Table of Contents Important PrecautionsPage Before YOU Begin Left Side Right SideAssembly Tighten all parts used in steps 2, 4, Operation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Diagram of the Console Battery InstallationInsert the key fully into the power switch Step by Step Console OperationReset the console and start the walking belt HOW to Change the Incline of the TreadmillCALORIES/FAT CAL Ories displayÑThisHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Maintenance and TROUBLE-SHOOTING Problem The power turns off during useTop Problem The walking belt slows when walked on Problem The walking belt is off-center when walked onProblem The walking belt slips when walked on HOW to Measure Your Heart Rate Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Part LISTÑModel No. PFTL38581 Key No. Qty DescriptionExploded DRAWINGÑModel No. PFTL38581 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT