ProForm 720 user manual 107

Page 7

5.Set the Console Base (101) on the Uprights (80, 84). Thread the four Upright Bolts (76) with four Internal Star Washers (77) into the Uprights and the Console Base.

Be careful not to pinch the Wires (not shown) in the Uprights. Tighten the two Upright Bolts indicated by the arrows first; then, tighten the remaining two Upright Bolts.

Make sure that the Left and Right Trays (109, 111) are pressed into the Console Base (101).

6.Fold the treadmill to the storage position (see page 21).

If the Wheels (94) are resting on the floor or if the tread- mill rocks slightly, turn one or both of the Leveling Feet (95) under the Upright Base (97) until the Wheels are off the floor and the rocking motion is eliminated. Note: If necessary, tip the treadmill and use a phillips screwdriver to turn the Leveling Feet.

5

 

101

 

 

 

 

 

 

 

84

 

111

109

 

 

 

77

 

 

77

 

 

76

80

76

77

 

 

 

6

 

 

 

 

 

97

 

 

95

94

 

 

 

 

7.Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may be included. Keep the included allen wrenches in a secure place. The large allen wrench is used to adjust the walking belt (see page 23). To protect the floor or carpet, place a mat under the treadmill. If there are thin sheets of clear plastic on the decals, remove them.

If you purchase the optional chest pulse sensor (see page 20), follow the steps below to install the receiver included with the chest pulse sensor.

1.Make sure that the power cord is unplugged. Remove the indicated Screw (108) and the Access Door (116).

2.Remove the paper from the adhesive pad on the back of the Receiver (A). Hold the Receiver so the small cylin- der is near the lower edge of the Receiver and facing the Console (107) as shown. Firmly press the Receiver onto the indicated corner of the Access Door (116).

Connect the wire on the Receiver to the indicated wire extending from the Console.

3.Make sure that no wires are pinched. Reattach the Access Door (116) with the Screw (108).

107

Wire

A

Wire

Cylinder

116

108

7

Image 7
Contents Model No. PFTL79021 Serial No QUESTIONS?Customer HOT Line Important Precautions Table of ContentsPage Right Side Before YOU BeginBack Make sure that the power cord is unplugged AssemblyUpright Base Legs remain in the Uprights107 HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerNext, stand on Foot rails Calories/PulseDistance/Incline dis Measure your heart rate if desiredSelect one of the preset programs HOW to USE Preset ProgramsSelect a heart rate program HOW to USE Heart Rate ProgramsFollow your progress with the displays Put on the chest pulse sensorTurn on the fans if desired Enter your age and a maximum speed settingHOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoHOW to Connect Your VCR Whenkey. the program is completed remove HOW to USE Programs Directly from OUR WEB Site Optional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingProblem The treadmill rocks during use Top Problem The walking belt slows when walked onExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Qty Description R0703AQty R0703A Exploded Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT