Viewing Your Results, Resetting Your Pedometer

VIEWING YOUR RESULTS

Once you put on your pedometer with the cover closed, it will automatically begin to record your steps, activity time, and distance. Repeatedly press the MODE button to cycle through the pedometer modes:

STEPS gTIME g DISTANCE g STEPS

Time and Distance are counted automatically whenever steps are being counted.

•TIME is time spent in step activity.

•DISTANCE is simply stride length x steps.

Note: For extra accuracy, the default Step Filter Setting is 1. See page 19 to learn more.

RESETTING YOUR PEDOMETER

Most people prefer to reset counts daily.To reset your counts: From STEP,TIME, or DISTANCE mode, press and hold the yellow RESET button for at least 2 seconds.You’ll see the values all go back to zero.

OTHER SETTINGS

The Step Filter and Unit of Measurement settings are accessed through a special “deep set” mode.

To enter this mode, press and hold the S1 button for 4 seconds.The screen will display a single digit. From within Deep Set mode, press the S2 button to cycle back and forth between the Step Filter set point and Choice of Unit System.

CHANGING STEP FILTER SETTING

While the JW200 PedometerEngine™ Step Sensor is extremely accurate, some people like to have the ability to filter out false steps. Therefore, the unit has a variable setting step filter, to allow fine-tuning to your specific preferences. You can set the value to any value from 0 – 5 steps. For example, if the filter is set to “3”, the unit will wait to start counting steps until more than three steps have been taken in less than five seconds.

Press S3+ (MODE) or S3– (RESET) to change the Step Filter Setting.

Can be set		DIGI-WALKERXL.COM
from 0-5	STEP	TIME DIST	SET
steps

“US” (English) or “EU” (Metric)

DIGI-WALKERXL.COM		140SXL
STEP TIME DIST	SET	140SXL
		JW200	S3-	S1,S2,S4	S3+
			S3-	S1,S2,S4	S3+

Set Step Filter set point

140SXL

JW200	S3-	S1,S2,S4	S3+

20Set measurement mode

CHANGING UNITS (English vs. Metric)

The Pedometer can display either in English units (in, mi, and lb

-this is the default), or in Metric units (cm, km, and kg). From within Deep Set mode (see pg. 18), press the S2 button to cycle back and forth between setting the Step Filter set point and Choice of Unit System.The unit will show either “US” or “EU” (for European Union) depending on the unit system chosen. If you change units after using the pedometer, the unit will convert all of your data into the new unit system when you exit Deep Set model.You can check to see which system of units you are using by seeing which measurement units are displayed on the Stride and Weight setting screens.

Press S3+ (MODE) or S3– (RESET) to change the Measurement Mode. Press and hold S4 for 2 seconds to exit Deep Set Mode.

Note:The unit will save any changes and exit set mode after 30

seconds unattended.

REPLACING THE BATTERY AND MASTER RESET

When the display starts to dim or goes blank, it is time to replace the battery.

If the display is not uniformly dim or blank, and appears to display “erroneous data”, do a Master Reset by pressing all 3 buttons simultaneously for 3 seconds and then release.

The display should go blank, then turn all segments on, then display 0 steps in Step Mode.

Note: All the settings will return to their default setting values. If you need to change the battery, the settings will also revert to default settings.

To replace the battery:

1.Insert a coin into the slot on the bottom of the case, and twist to loosen the faceplate. Remove

faceplate and set aside.

	2. Locate the battery holder as seen	Battery
	on sketch. Pull out the old battery,	Battery
	on sketch. Pull out the old battery,
	and push a new LR-44 battery into the holder,
	with positive terminal (+) facing up.

3.Snap faceplate back into place, hooking the bottom two tabs first, then closing by pressing together at the top two tabs.