Seiko s056 manual Automatic SHUT-OFF Function, Timer Setting, Hour Minutes Seconds

DOUBLE REPEAT TIMER (for Cal. S057)

●Two timers are available for use either individually or in combination. When used together, Timer 2 starts counting down as soon as Timer 1 has finished counting down the set time. They repeat their respective countdown cycles alternately as many times as necessary unless stopped.

●Each Timer 1 and Timer 2 can be set for any desired amount of time from 10 seconds up to 99 hours, 59 minutes and 59 seconds in one-second increments.

●To use either Timer 1 or Timer 2 as a standard repeat timer, set the timer not in use to “00:00’00.”

●The number of times that the timers repeat their countdown cycles can be set from 1 to 100 times. If “---“ is set for the number of repeating times, the timers will automatically start over a new counting until stopped by the user.

TIMER SETTING

DPress to show the TIMER display.

▼

BPress and hold for 2 seconds to show the TIMER SETTING display.

*The HOUR digits for Timer 1 start flashing.

▼

CPress repeatedly to select the digits (flashing) to be adjusted.

Number of times		Number of times
the countdown		the countdown is
was repeated	B	to be repeated
A		C

Timer 1

	HOUR	MINUTES	SECONDS	HOUR	MINUTES
	(TIMER 1)	(TIMER 1)	(TIMER 1)	(TIMER 2)	(TIMER 2)
	NUMBER OF TIMES THE				SECONDS
▼	COUNTDOWN IS TO BE REPEATED				(TIMER 2)

APress to set the flashing digits.

*The digits move quickly if Button A is kept pressed.

*By pressing Button D while the digits are flashing, both of the timers and the number of times the ▼ countdown is to be repeated will be reset to “00:00'00"” and “000,” respectively.

BAfter all the adjustments are completed, press to return to the TIMER display.

Timer 2

D

●The timers cannot be set for a time less than 10 seconds. If a time less than 10 seconds is set and Button B is pressed to return to the TIMER display, the timers will automatically be set to “00:00'10".”

How to use the timer

In this way, both the timers repeat the countdown the number of times you have set, showing the number of times the countdown has been completed on the display.

C

Press Button C to start	mark flashes during
Timer 1.	the countdown.

A time-up warning beep for Timer 1 sounds 3 seconds before the set time is up. When the set time is up, time-up beep for Timer 1 sounds for 5 seconds.

T I M E R 2 s t a r t s counting down.

A time-up warning beep for Timer 2 sounds 3 seconds before the set time is up. When the set time is up, time-up beep for Timer 2 sounds for 5 seconds.

TIMER 1 starts counting down.

●To stop the time-up warning beep and time-up beep while sounding, press either Button A, B, C or D. This will not affect the time-up beeps for the subsequent countdown cycles.

●The time-up beeps of Timer 1 and Timer 2 sound in different tones.

●Restarting and stopping the timer can be repeated as many times as necessary by pressing Button C.

AUTOMATIC SHUT-OFF FUNCTION

▲

Automatic shut-off mark

When the automatic shut-off function is set to “ON,” this mark appears in any display mode except while the stopwatch is in the setting mode.

When the automatic shut-off function is set to “ON” in the TIME/CALENDAR SETTING display, the following energy-saving functions will be activated to help extend the battery life.

●Regardless of the display modes, when the stopwatch is left untouched for one hour, the display becomes blank in order to minimize battery consumption.

●The current time will be displayed once every 10 seconds even while the display is blank, to indicate that the blank display is not caused by battery exhaustion.

●While the stopwatch or timer is measuring, the display will not become blank for the energy-saving functions.

●To return to the normal display, press either Button A, B, C or D. The last display before it became blank will be shown.

4