Timex W-104 warranty Interval Timer, Alarm, Indiglo NIGHT-LIGHT/NIGHT-MODE Feature

TIMER

1.Press MODE until TIMER appears.

2.Press SET/RECALL. Hour digits flash.

3.Press + / – to change hour.

4.Press NEXT and + / – to set minutes.

5.Press NEXT and + / – to set seconds.

6.Press NEXT and + / – to select STOP AT END or REPEAT AT END or CHRONO AT END.

7.Press DONE to confirm and exit.

8.Press START/SPLIT to start Timer. Timer will continue to run if you exit Timer mode.

9.An alarm melody chimes when Timer reaches zero or before it starts to countdown again.

10.Press STOP/RESET to stop Timer. Press and hold to reset.

11.Press SET/RECALL to change countdown time.

TIPS: • appears in Time display when Timer is running.

•For repeat Timer operation, repetition number appears at bottom right of screen in both countdown and interval Timers.

•Maximum number of repeats is 199.

•In Chrono at End, the display switches to the CHRONO mode at the end of the countdown if Chrono has been reset.

INTERVAL TIMER

You can set multiple Timers that countdown in sequence.

1.Press MODE until INTTMR appears.

2.Set countdown time as in Timer mode above.

3.With interval number flashing, press +/– to set other intervals.

4.Press DONE to complete setting.

5.Press START/SPLIT to start Interval Timer. Other operations are the same as for Timer mode. TIPS: • When first countdown is complete, Timer proceeds to the next non-zero interval that is set.

INDIGLO flashes and beep sounds between each interval.

•Settings (e.g. REPEAT AT END) of any Interval Timer apply to the entire sequence of intervals.

ALARM

1.Press MODE until ALM 1 appears.

2.Press SET/RECALL to set alarm.

3.Hour digits flash. Press + / – to change hour.

4.Press NEXT and + / – to set minutes, AM or PM (if primary time display is in 12-hour format), DAILY, WKDAYS, WKENDS, or day of the week (weekly alarm).

5.Press DONE to confirm and exit.

6.Press START/SPLIT or STOP/RESET to turn Alarm ON or OFF.

7.To set remaining alarms, press MODE for ALM 2 or ALM 3 and set as above.

TIPS: • When Alarm is on, appears in Time display.

•When Alarm goes off, INDIGLO® night-light and alarm icon flash and alert sounds. Press any button to silence.

•If no button is pushed, alert will cease after 20 seconds and Backup Alarm will activate after 5 minutes.

INDIGLO® NIGHT-LIGHT/NIGHT-MODE® FEATURE

1.Press INDIGLO to activate night-light. Electroluminescent technology (U.S. pat. 4,527,096 and 4,775,964) illuminates entire watch face at night and in low light conditions.

2.Continue to press up to 3 seconds to maintain illumination.

3.Press and hold INDIGLO for 4 seconds to activate NIGHT-MODE® feature (U.S. pat. 4,912,688) feature. will appear.

4.In NIGHT-MODE® feature, push any button to illuminate watch face for 3 seconds.

5.To deactivate NIGHT-MODE® feature, press INDIGLO for 4 seconds. Feature will automatically deactivate after 8 hours.

WATER & SHOCK RESISTANCE

If your watch is water-resistant, meter marking or (		) is indicated.
	Water-Resistance Depth	p.s.i.a.* Water Pressure Below Surface
	30m/98ft	60
	50m/164ft	86
	100m/328ft	160

*pounds per square inch absolute

WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY BUTTONS UNDER WATER.

1.Watch is water-resistant only as long as lens, push buttons and case remain intact.

2.Watch is not a diver watch and should not be used for diving.

3.Rinse watch with fresh water after exposure to salt water.

4.Shock-resistance will be indicated on watch face or caseback. Watches are designed to pass ISO test for shock-resistance. However, care should be taken to avoid damaging crystal/lens.