4.Press S3 button, the geographical RE- GION will blink.
5.Press S1 button or S2 button to move forward or backward respectively the REGION to be selected.
6.Press S3 button, the geographical LOCA TION will blink.
7.Press S1 button or S2 button to move forward or backward respectively the LOCATION to be selected.
8.Press S3 button, the DST (daylight sav ings time) status will blink.
9.Press S1 button or S2 button to move forward or backward respectively the DST status to be selected. If AUTO is se- lected, the watch shall
determine when the location is on DST; if OFF or ON is selected, the DST status is forced to the selected status all the
time. Please note that the current DST status is shown with the DST flag.
10.Press S3 button, the custom location selection will blink.
11.Press S1 or S2 button to toggle between YES and NO. If NO is selected, that step is the end of the setting se quence. Otherwise, the sequence con tinues to allow setting the time offset to the tide data and the 16 characters of the custom location name.
12.Press S3 button, the time offset (in the unit of minutes) to the tide data for the custom location will blink.
13.Press S1 button or S2 button to increase or decrease respectively the time offset (the available offsets are
14.Press S3 button, the first character of the
15.Press S1 button or S2 button to cycle forward or backward respectively the selected character. Press S3 button to proceed to the next character.
16.After finished making all the settings, press S4 button to confirm the settings.
TO USE THE CHRONOGRAPH
For the measurement of elapsed time,
1.Press S3 button to select CHRONO GRAPH mode.
2.Press S1 button to start counting.
3.To stop counting, press S2 button. Press S1 button to resume from where it left off.
4.To reset to zero, press S2 button once to stop counting and then press S2 but- ton again.
NOTE: For the first hour, the CHRONO time is displayed in the MM.SS hh (minutes. second hundredths) format. After one hour, the CHRONO time is displayed in HH:MM SS (hours:minutes.seconds) format.
NOTE: The CHRONO can count up to a maximum time of 99:59.59 (99hours:59minutes.59seconds).
TO SET THE TIMER
1.Press S3 button to select TIMER mode.
2.Press S4 button, the “SET” message appears and the Hour digits blink on the display.
3.Press S1 button to increase the digits by one unit, or press S2 button to decrease the digits by one unit. Holding down either button will speed up the process.
4.Press S3 button once, the Minute digits will blink on the display.
5.Press S1 button or S2 button to set the Minute digits.
6.Press S3 button once, the Second digits will blink on the display.
7.Press S1 button or S2 button to set the Second digits.
8.Press S3 button once, the action to be taken at the end of a countdown will
blink.
9.Press S1 button or S2 button to toggle between STOP and REPEAT. If STOP is
selected, the TIMER stops; if REPEAT is
selected, the TIMER repasts its count down for 99 times.
10.After finished making all the settings, press S4 button to confirm the settings.
NOTE: The TIMER can count up to a maximum time of 23:59.99 (23hours:59minutes.59seconds).
TO USE THE TIMER
1.Press S3 button to select TIMER mode.
2.Press S1 button to start a countdown.
3.To stop counting, press S2 button once. Press S1 button to resume from where it left off.
4.To reset the TIMER, press S2 button once to stop counting and then press S2 but- ton again.
5.Upon completion of a countdown, if STOP is selected as the action to be taken, the TIMER stops at zero ,a tune will be emitted and the backlight
will flash; if REPEAT is selected, the TIMER repeats its countdown with the rep number updated. If the TIMER reset time is less than 30 seconds, a beep will be emitted. Otherwise, a tune will be emitted and the backlight will flash.
TO SET THE HEAT TIMER
1.Press S3 button to select HEAT TIMER mode.
2.Press S4 button, the “SET” message appears and the Minute digits blink on the display.
3.Press S1 button to increase the digits by five units, or press S2 button to decrease the digits by five units. Holding down either button will speed up the process.
4.After finished making all the settings, press S4 button to confirm the settings.
NOTE: The HEAT TIMER can count up to a maximum time of 35.00 (35minutes).
TO USE THE HEAT TIMER
1.Press S3 button to select HEAT TIMER mode.
2.Press S1 button to start a countdown.
3.To stop counting, press S2 button once. Press S1 button to resume from where it left off.
4.To reset the HEAT TIMER, press S2 but ton once to stop counting and then press S2 button again.
5.Upon completion of a countdown, a tune will be emitted and the backlight will flash.
NOTE: The HEAT TIMER is independent of the TIMER. Both may be running at the same time.
TO SET THE ALARM TIME
1.Press S3 button to select ALARM mode.
2.Press S4 button, the “SET” message ap pears and the alarm entry to set blinks on the display.
3.Press S1 button or S2 button to toggle between ALARM 1 and ALARM 2.
4.Press S3 button, the Hour digits (includ ing AM/PM for
5.Press S1 button to increase the digits by one unit, or press S2 button to decrease
the digits by one unit. Holding down either button will speed up the process.
5.Press S3 button, the Minute digits will blink.
6.Press S1 button or S2 button to set the Minute digits.
7.Press S3 button, the alarm frequency will blink.
8.Press S1 button or S2 button to cycle forward or backward respectively the alarm frequency to be selected (DAILY, WEKDAYS, WEEKENDS, day of the week and WKLY).
9.After finished making all the settings, press S4 button to confirm the settings.
NOTE: The ALARM TIME displayed is in the same Time Format as the primary time.
NOTE: A tune will go off and the backlight will flash for 20 seconds at the designated
ENGLISH
time when the ALARM is activated.
NOTE:The alarm will automatically be activated after being set.
WHEN AN ALARM OR HOURLY CHIME GOES OFF
A tune will go off by the hour if the Hourly Chime function is activated and the same will happen at the designated time when the ALARM is activated. To stop the tune, press any button.
If the alarm tune is done without any user interruption, the watch will automatically enter a snooze mode. The ALARM will go off again after 5 minutes but for only once.
TO USE THE BACKLIGHT
Press S5 button to turn on the backlight for three seconds.
| |
To reduce carbon foot print, these | FS8124 |
Freestyle instructions are printed with | |
soy inks on recycled paper. |
|