Freestyle 789 operating instructions Ltrt Lbrb, Normal Time Mode, HOW to Operate Countdown Timer

789SHARK™ INSTRUCTIONS

FEATURES:

•CURRENTTIME (HR., MIN.,

&SEC.)

•DAY/MONTH/DATE

•CHRONOGRAPH WITH SPLIT

&LAP TIMES

•DUALALARMS ( 1 DAILY REPEATING, 1 NON-

REPEATING REMINDER.)

•COUNTDOWN, COUNTDOWN REPEAT, COUNTDOWN CHRONO

LAP & COUNTDOWN CHRONO SPLITTIMERS

•DUAL TIME

•HOURLY CHIME

•OPTIONAL24-HR. TIME (MILITARYTIME. )

•WATER RESISTANT TO 300 FT.

•NIGHT VISION™ ELECTRO- LUMINESCENT BACKLIGHTING

NORMAL TIME MODE

( The term “Mode” means the func- tion status of the watch.) Normal time mode shows hours, minutes, seconds, day and date. To set time, see operating instructions on How to Set Normal Time.

LTRT

LBRB

NORMAL TIME MODE

KEY TO SYMBOLS

LT - Left Top (Light/Set)

LB - Left Bottom (Mode)

RT - Right Top (Start/Stop)

RB - Right Bottom (Lap/Reset)

HOW TO SETNORMAL TIME, DATE AND 24-HOUR FORMAT Note: While in the setting mode, the Night Vision™ backlight will remain illuminated. If no buttons are pressed for approximately ten seconds, the watch will exit the setting mode.

From Normal Time mode, press and hold the light/set button LT for approximately three seconds; the seconds digits will flash. Pressing the Start/Stop button RT will reset the seconds digits to 0. If seconds are greater than 30, one will be added to the minutes digit.

LTRT

LBRB

To set minutes, press Mode button LB; single minutes digit will flash. To advance flashing minutes digit, press Start/Stop button RT;hold for rapid

advance.

LTRT

LBRB

To set tens of minutes, press Mode button LB; tens of minutes will flash. To advance flashing tens of minutes

LTRT

LBRB

press Start/Stop button RT; hold for rapid advance.

Continuing through the setting mode, the setting sequence is a continuous loop of: seconds • single minutes • tens of minutes • hours • day/month/date • 12/24-hour mode, and looping back to seconds. When setting is complete, press Light/Set button LT to return to normal time mode.

HOW TO OPERATE CHRONOGRAPH/STOPWATCH

The chronograph will record a maximum of 99 hours, 59 minutes and 59 seconds. Press Mode button LB once from normal time mode to enter the chronograph mode. Normal time will remain on

LTRT

LBRB

the lower row, chronograph on the upper row. “CH” flag will bedisplayed. Reset the chronograph to zero by pressing Lap/Reset button RB. Press the Light/Set button LT to switch between Lap and Split mode.

LTRT

LBRB

(“LAP” flag will be displayed for lap mode and “SPL” flag will be displayed for split time mode.)

Split time is the time elapsed since the start of the chronograph. To use the split time feature, “SPL”flag must be displayed. Press Start/Stop button RT to start chronograph. “SPL” flag will begin flashing. Press Lap/Reset button RB to view split time. Chronograph will continue to count while split time is displayed. To release split time and return to running chrono- graph, press Lap/Reset button RB.

LTRT

LBRB

Each press of Lap/Reset button RB will display a split time.

To stop chronograph, press Start/Stop button RT. Reset the chronograph to zero by pressing the Lap/Reset button RB. Lap time is the time elapsed since the previous lap. To use the lap time feature, “LAP” flag must be displayed. Reset the chronograph to zero by pressing the Lap/Reset button RB. Enter LAPmode by pressing Light/Set button LT. Press Start/Stop button RT to start chronograph. “LAP” flag will begin flashing. Press Lap/Rest button RB to view lap time. Chronograph will start counting next lap while lap time is displayed. To release lap time and return to running chrono, press Lap/Reset button RB. Each press of Lap/Reset button RB will display a lap time.

LTRT

LBRB

To stop chronograph, press Start/Stop button RT. Reset the chronograph to zero by pressing the Lap/Reset button RB.

HOW TO SET AND OPERATE THE ALARMS AND HOURLY CHIME From normal time mode, press Mode button LB twice to enter the alarm mode. Normal time remains on the lower row, alarm time on the upper row. Pressing Lap/Reset but- ton RB will toggle between alarm 1, indicated by “A1” flag, and alarm 2, indicated by “A2” flag. Alarm 1 is a daily, repeating alarm,and alarm 2

LTRT

LBRB

is a one time only reminder alarm.

Press and hold Light/Set button LT for approximately three seconds to enter alarm setting mode. The min- utes digit will flash. Press Start/Stop button RT to advance the flashing minutes digit.

LTRT

LBRB

Press Mode button LB to advance tens of minutes. Press Start/Stop button RT to advance the flashing tens of minutes digit.

LTRT

LBRB

Press mode button LB to advance the hours digit. Press Start/Stop button RT to advance the flashing hours digit. While setting the flashing hours digit, “A” or “P” is displayed next to alarm. “A” designates a.m. and “P” designates p.m.

LTRT

LBRB

Press Light/Set button LT to exit the alarm setting mode. To activate the alarm while in alarm mode: Press Start/Stop button RT to activate the alarm ((•)) and/or hourly chime .

LTRT

LBRB

Note the setting sequence is: alarm on, chime on, both alarms on, both alarms andchime off.

Again, press Lap/Reset button RB to toggle between alarm 1 and alarm 2. Alarm 2 is set and activated the same way as alarm 1. A1 ((•)) = alarm 1 set.

A2 ((•)) = alarm 2 set.

A1 A2 ((•)) = alarm 1 & 2 set. = hourly chime on.

HOW TO OPERATE THE

COUNTDOWN TIMER

Press Mode button LB three times from the normal time mode to enter the countdown timer mode. Normal time will remain in the lower row and the timer will appear on the

continued...