JVC MX-K10 manual Standard Recording, CD Synchro Recording, Tape to Tape Recording DUB- Bing

Page 20

Using the Cassette Deck (Recording)

Standard Recording

This is the basic method for recording any source. The System also has special ways for recording CD to tape, and tape to tape, which save you time and effort, as well as give you some special effects. However, when you need to add a selection to a tape you have made, or are combining selections from several sources on one tape, use the method described below; just substitute the source you want into this procedure, such as a tape in Deck A, a CD, or the Tuner. You can also record from an external equipment with this procedure.

To Record Any Sound Source to Tape

Follow these steps to record from any sound source onto a tape in Deck B.

1 Insert a blank or erasable tape into the Deck B and wind past the tape leader.

Tape travelling direction

2 Prepare the source, by, for example, tuning in a radio station, loading CDs, or turning on connected equipment.

•For CD recording, see “CD Synchro Recording” mentioned below.

•For dubbing, see “Tape to Tape Recording (DUBBING)” described below.

3 Press the REC START/STOP button on the Unit.

The “REC” indicator lights up and the System begins record- ing.

The Tape indicator (3) blinks on the display.

•If the tab of the cassette tape on the Deck B is removed to prevent erasure or recording, "NO REC" will appear on the display.

To stop during recording, press the REC START/STOP but- ton on the Unit, or press the 7 button.

Recording an AM Station to Tape (Beat Cut)

When recording an AM broadcast, beats may be produced which are not heard when listening to the broadcast. If this happens, press the PROGRAM button on the Unit to eliminate the beats.

1 Set to AM station and start recording.

2 Press the PROGRAM button on the Unit to eliminate the beats.

Each time you press the button, the display changes as shown below:

CUT 1= CUT 2 = (back to the beginning)

CD Synchro Recording

Everything on the CD goes onto the tape in the order it is on the CD, or according to the order you have set in a program.

1 Prepare CDs. (See page 12.)

Press the CD1-3 button (that you want to make recording), and then press the 7 button.

•If you want to record specific tracks only, you need to pro- gram the tracks beforehand. (See page 14.)

2 Insert a blank or erasable tape into the Deck B and wind past the tape leader.

3 Press the CD REC START button on the Unit.

“CD REC” appears on the display and the “REC” indicator lights up. Then, the System begins CD Synchro Recording and the tracks on the CD are recorded on the tape.

When recording of the tracks of all CDs is finished, “CD REC FINISHED” scrolls on the display and the CD Player and Cas- sette Deck stop.

(When finished)

CD

REC START

•If the tab of the cassette tape on the Deck B is removed to prevent erasure or recording, "NO REC" will appear on the display.

•After the CD Player has played the entire CD or all the pro- grammed tracks, the tape automatically stops.

To stop at any time during the recording process, press the REC START/STOP button on the Unit or the 7 button. “CD REC FINISHED” scrolls on the display and the CD Player and Cassette Deck stop.

•When making SLEEP timer settings while doing CD Syn- chro recording, set enough time to allow for the CD to fin- ish playing, otherwise the power will go off before recording is completed.

Tape to Tape Recording (DUB- BING)

Recording from one tape to another is called dubbing. You can dub tapes simply, with just a single button.

1 Press the TAPE3 button, and then press the

7button.

2 Insert the source cassette you want to copy from into Deck A for playback.

3 Insert a blank or erasable cassette you want to copy onto into Deck B for recording.

4 Press the DUBBING button on the Unit.

Deck A and Deck B will start simultaneously and the "REC" indicator lights up.

During dubbing, the Deck indicators "A" and "B" light up al- ternately.

•If no tape is inserted into Deck A, "NO TAPE" will appear on the display.

•If no tape is inserted into Deck B, "NO TAPE" will appear on the display.

To stop dubbing, press the REC START/STOP button on the Unit or the 7 button.

•During dubbing, you can hear sound effects through the speakers or headphones. However, the sound is dubbed without sound effects.

18

Page 19 Page 21
Image 20
Page 19 Page 21
Contents MX-K10 LASERCLASS1PRODUCT How This Manual Is Organized FeaturesIntroduction Table of Contents Accessories How To Put Batteries In the Remote ControlGetting Started R6PSUM-3/AA15FUsing the Remote Control Connecting the FM AntennaUsing the Supplied Wire Antenna Using an FM 75-Ohm Antenna Cable not SuppliedConnecting the AM Antenna Connecting the SpeakersRear Panel of the Unit Right side rear view Red BlackConnecting External Equipment Connecting to the Wall OutletDemo Mode Compu PlayBasic Operations Turning the Power On and OffAdjusting the Volume Selecting the Sound Mode Entering the Number with the Remote Control Numeric KeysFade-out Muting Fade Muting Reinforcing the Bass Sound Active Bass EXUsing the Tuner Tuning In a StationSelect a station using one of the following methods One Touch RadioPresetting Stations To Change the FM Reception ModeUsing the Unit Press the 4 or ¢ button to select the preset numberUsing the CD Player About the Disc IndicatorDisc Number indicator Lights all the time Play mode Repeat IndicatorTo Load CDs To Unload CDsExample of indication One Touch PlayBasics of Using the CD Player- Normal Play To Play CDsTo Select a Track Search PlayProgramming the Playing Order of the Tracks To Make a ProgramTo Play the Program You Have Made To Exit and Re-enter Program PlayRandom Play Repeating TracksTray Lock Function Locking the TrayUsing the Cassette Deck Listening to a Tape Playing a TapeTo Fast-Wind a Tape Close the cassette holder gentlyUsing the Cassette Deck Recording REC indicator Tape indicator Eject Deck BThings To Know Before You Start Recording Eject Deck aStandard Recording CD Synchro RecordingTape to Tape Recording DUB- Bing To Record Any Sound Source to TapeUsing an External Equipment Listening to the External EquipmentUsing the Timers Setting the ClockPress the CLOCK/TIMER button REC Recording TimerSetting the Daily Timer Setting the on time ExampleSetting the OFF time Example Selecting the music sourceSetting the REC Recording Timer Turning the Daily Timer On and OffSetting the volume level Press the SET button on the UnitTurning the REC Recording Timer On and Off Setting the on time you want the System to turn onSetting the OFF time you want the System to turn off Select the preset station for recordingSetting the Sleep Timer Timer PriorityDuring playback a source, press the Sleep button Wait for 5 secondsCare And Maintenance Troubleshooting Specifications

MX-K10 specifications

The JVC MX-K10 is a compact yet powerful home audio system that combines modern technology with a sleek design. Released in the early 2000s, the MX-K10 has remained popular among audiophiles and casual listeners alike for its impressive performance and versatility.

One of the standout features of the JVC MX-K10 is its dual cassette decks, which allow users to play and record tapes with ease. This feature appeals to nostalgic consumers who still enjoy physical media and want to preserve their cassette collections. The unit includes a high-speed dubbing function, enabling users to copy their favorite cassettes quickly, without compromising sound quality.

In addition to the cassette decks, the MX-K10 also supports CD playback, accommodating the transition from analog to digital media. The system can play various CD formats, including audio CDs and CD-R/RW. The inclusion of a programmable memory feature allows users to create custom playlists, making it convenient to listen to favorite tracks without interruptions.

The audio output is powered by an impressive integrated amplifier that delivers robust sound quality. With a peak power output of up to 110 watts, the MX-K10 offers dynamic audio performance, ensuring that users experience rich bass and clear treble across a range of music genres. The system features a 3-band equalizer, providing listeners with the ability to fine-tune their audio experience according to their preferences.

Connectivity is another strong point of the JVC MX-K10. It offers multiple input options, including auxiliary inputs, which allows users to connect external devices such as smartphones and tablets. The built-in FM/AM tuner provides access to radio stations, broadening the listening options available to users.

The design of the MX-K10 is both stylish and functional. The compact unit fits easily into any room layout, while its clean lines and modern aesthetics make it an attractive addition to home decor. The front-facing display is easy to read, providing essential information at a glance, including track number and radio frequency.

Overall, the JVC MX-K10 is a versatile and reliable audio system, offering an array of features that cater to both modern and classic media formats. Its enduring popularity speaks to its quality and performance, making it a notable choice for anyone seeking an impressive home audio experience.
Top Page Image Contents