ProForm PFEX25122 user manual Damaging, Reed Switch Wire 31, make sure that it is, Any slack

Page 6

2.Attach the Frame Extension (84) to the Frame (1) with six M10 x 22mm Button Screws (80) and six M10 Split Washers (54).

Attach the other Stabilizer (19) to the Frame Extension (84) with two M10 x 75mm Carriage Bolts (65) and two M10 Nylon Locknuts (64).

3.Attach the Seat (20) to the Seat Post (6) with four M8 Nylon Locknuts (66) and four M8 Split Washers (81). Note: The Nylon Locknuts and Split Washers may be preattached to the Seat.

Turn the Seat Knob (29) counterclockwise two or three turns to loosen it. Next, pull the Seat Knob, insert the Seat Post (6) into the Frame (1), and then

release the Seat Knob. Move the Seat Post up and down slightly until it locks into position.

Push the Seat Guide (46) into the top of the Frame

(1). Secure the Seat Guide to the Frame with an M4 x 4mm Screw (70). Then, tighten the Seat Knob.

4.Apply a small amount of the included grease to the Handlebar Axle (33). Insert the Handlebar Axle into

the Frame (1) and center it.

To

avoid

damaging

the Reed Switch Wire (31), make sure that it is

positioned as shown in the inset drawing.

 

 

(Note:

It may be helpful to use a rubber mallet to

insert

the

Handlebar Axle.)

 

 

 

While another person holds the Upright (2) in the position shown, connect the Extension Wire (39) to

the Reed Switch Wire (31). Carefully pull the upper end of the Reed Switch Wire to remove

any slack.

Set the Upright (2) on the Frame (1);

be careful not

to pinch the Extension Wire (39) or the Reed

 

Switch Wire (31).

Attach the Upright with three M10

x 17mm Button Screws (55) and three M10 Split Washers (54).

2

 

 

 

 

 

 

 

1

54

80

 

 

 

 

 

64

 

 

 

 

 

 

19

 

54

 

 

84

 

 

 

 

 

 

 

80

54

64

 

 

 

 

 

 

 

 

 

80

 

 

65

3

 

 

 

 

 

 

 

20

 

 

 

 

 

 

 

 

6

 

 

70

 

 

81

 

 

 

 

66

 

 

29

 

 

 

 

 

46

 

 

 

 

 

 

 

 

 

 

1

 

4

 

 

 

 

Side

 

2

 

 

31

Shield

 

 

 

 

 

 

 

55

 

1

 

 

 

 

 

 

55

54

54

 

33

 

 

 

 

 

 

 

 

 

 

 

 

39

 

Grease

 

 

 

31

 

 

 

 

 

 

 

 

 

 

33

 

 

 

 

1

 

 

 

6

Image 6
Contents Through QUESTIONS?Model No. PFEX25122 Serial No Customer HOT LineTable of Contents Important Precautions Exercise cycle is intended for in-homePulse sensor is not a medical device Back Before YOU BeginFront Right SideAssembly Assembly requires two personsRecommended Damaging Reed Switch Wire 31, make sure that it isSwitch Wire Any slackBattery compartment Drawing Handlebars are on the correct sidesOnto each end of the Handlebar Axle Tighten an M8Handlebar Operation Dual-action ModeStationary Mode Description of the ConsoleBattery Installation HOW to Operate the ConsoleSteadily Console Troubleshooting Adjusting the BeltAdjusting the Reed Switch Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyHamstring Stretch Suggested StretchesToe Touch Stretch Calf/Achilles StretchExploded DRAWING-Model No. PFEX25122 Description Key No. QtyR1102A 6673Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT HOW to Order Replacement PartsLimited Warranty Part No R1102A