Diamondback Single-Speed Bicycle manual Removing a Bolt‑On Rear Wheel with Coaster Brake, Pedals

Page 18

and squeeze the brake lever to make sure the brake is functioning correctly.

6.Removing a BoltOn Rear Wheel with Coaster Brake

a.Disengage the coaster brake arm from its frame bracket

(see fig. 15).

b.With a correctly sized socket, box, open end or adjustable wrench, loosen the two axle nuts.

c.Push the wheel forward to slacken the chain, and remove the chain from the chainring and wheel sprocket.

d.Pull the wheel out of the frame.

7.Installing a BoltOn Rear Wheel with Coaster Brake

a.Put the chain on to the wheel sprocket. Then, insert the wheel into the frame dropouts and push it all the way in to the dropouts. The axle nut washers should be on the outside, between the frame and the axle nut.

b.Put the chain on to the chainring.

c.Pull the wheel back in the dropouts so that it is straight in the frame and the chain has about 1/4 inches of up-and- down play.

d.Secure the coaster brake arm to its frame bracket (see fig. 15), but do not fully tighten the securing nut and bolt.

e.Tighten the axle nuts as tightly as you can, using a correctly sized socket, box, open end or adjustable wrench. Spin the wheel to make sure it is straight in the frame.

f.Fully tighten the coaster brake arm securing nut and bolt and check to make sure the brake is functioning correctly.

C.Pedals

1. Toe Overlap is when your toe can touch the front

wheel when you turn the handlebars to steer while a pedal is in the forwardmost position. This is common on small-framed bicycles, and is avoided by keeping the inside pedal up and the outside pedal down when turning.

!WARNING: Toe Overlap could cause you to lose control and fall. If you have toe overlap, exercise extra care when turning. A brake rotor (see Section 4.A.2.b) may also decrease the clearance between the front wheel and the pedal when the wheel is turned backwards.

2.Some higher performance bicycles come equipped with pedals that have abrasive and potentially dangerous surfaces. These surfaces are designed to add safety by increasing adhesion between the rider’s shoe and the pedal. If your bicycle has this type of high-performance pedal, you must take extra care to avoid serious injury from the pedals’ sharp surfaces. Based on your riding style or skill level, you may prefer a less aggressive pedal design. Your dealer can show you a number of options and make suitable recommendations.

3.Clipless pedals (sometimes called “step-in pedals”) are another means to keep feet securely in the correct position for maximum pedaling efficiency. They look like ski bindings ... a plate on the sole of the shoe clicks into a spring- loaded fixture on the pedal ... but unlike ski bindings, they only engage or disengage with a very specific motion which must be practiced to become instinctive. Clipless pedals require shoes and cleats which are compatible with the make and model pedal being used.

Many clipless pedals are designed to allow the rider to adjust the amount of force needed to engage or disengage the foot. Follow the pedal manufacturer’s instructions, or

18

Image 18
Contents For Single-speed bicycles Read it before you take the first ride On your new bicycleGeneral Warning Special note for parentsContents First Safety firstMechanical Safety Check Bike fitAsk someone with experience to check First rideSafety Riding SafetyWear safety gear appropriate to the kind of riding Wet Weather Riding Night RidingBicycling in Traffic Downhill, Stunt or Competition BikingChanging Components or Adding Accessories FitStandover height Saddle positionHandlebar height and angle Tech Brake reachBrakes Adjusting your coaster brake Hand Brakes How hand brakes workMechanical Safety Check, have your dealer check the brakes Wheels Front Wheel Secondary Retention Devices Removing a Bolt‑On Front WheelInstalling a Bolt‑On Front Wheel Installing a Bolt‑On Rear Wheel with Hand BrakeRemoving a Bolt‑On Rear Wheel with Hand Brake Installing a Bolt‑On Rear Wheel with Coaster Brake Removing a Bolt‑On Rear Wheel with Coaster BrakePedals Page Page Service Tire ValvesService Intervals Before every ride Mechanical Safety CheckIf your bicycle sustains an impact Driveway Rideout Appendix aLessons Turning Without WarningFollowing the Leader SummaryAppendix B Page Appendix C Installing a Quick Release Front Wheel Removing a Quick Release Rear Wheel Seatpost Quick Release Raleigh America, Inc. Bicycle Limited Warranty