Diamondback 2008-2005 manual Installing a Quick Release Front Wheel

Page 29

a matching hole in the front fork dropout (fig. 12c).

Ask your dealer to explain the particular secondary retention device on your bike.

!WARNING: Removing or disabling the secondary retention device is extremely dangerous and may lead to serious injury or death. It also may void the warranty.

2.Removing and Installing Quick Release Wheels a. Removing a Quick Release Front Wheel

(1)If your bike has rim brakes, disengage the brake’s quick- release mechanism to open the clearance between the wheel rim and the brake pads (See Section 4.A

figs. 7 through 10).

(2)Move the wheel’s quick-release

lever from the locked or CLOSED position to the OPEN position (figs. 20a & b).

(3)If your front fork does no have a secondary retention device go to step (5).

(4)If your front fork has a clip-on type secondary retention device, disengage it and go to step (5). If your front fork has an integral secondary retention device, loosen the tension adjusting nut enough to allow removing the wheel; then go to the next step.

(5)Raise the front wheel a few inches off the ground and tap the top of the wheel with the palm of your hand to knock the wheel out of the fork.

b.Installing a Quick Release Front Wheel

!CAUTION: If your bike is equipped with disk brakes, be careful not to damage the disk, caliper or brake pads when re-inserting the disk into the caliper. Never activate a disk brake’s control lever unless the disk is correctly inserted in the caliper. See also Section 4.A.

(1)Move the quick-release lever so that it curves away from the wheel (fig. 20b). This is the OPEN position.

(2)With the steering fork facing forward, insert the wheel between the fork blades so that the axle seats firmly at the top of the slots which are at the tips of the fork blades — the fork dropouts. The quick-release lever should be on the left side of the bicycle (fig. 20a & b). If your bike has a clip-on type secondary retention device, engage it.

(3)Holding the quick-release lever in the OPEN position with your right hand, tighten the tension adjusting nut with your left hand until it is finger tight against the fork dropout (fig. 19).

(4)While pushing the wheel firmly to the top of the slots in the fork dropouts, and at the same time centering the wheel rim in the fork, move the quick-release lever upwards and swing it into the CLOSED position (fig. 19 & 20a). The lever should now be parallel to the fork blade and curved toward the wheel. To apply enough clamping force, you should have to wrap your fingers around the fork blade for leverage, and the lever should leave a clear imprint in the palm of your hand.

!WARNING: Securely clamping the wheel takes considerable force. If you can fully close the quick release without wrapping your fingers around the fork blade for leverage, and the lever does not leave a clear imprint in the palm of your hand, the tension is insufficient. Open the lever; turn the tension adjusting nut clockwise a quarter turn; then try again.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Read it before you take the first ride On your new bicycle For BMX bicyclesSpecial note for parents General WarningContents Mechanical Safety Check Safety firstFirst Bike fitFirst ride Ask someone with experience to checkRiding Safety SafetyWear safety gear appropriate to the kind of riding Night Riding Wet Weather RidingDownhill, Stunt or Competition Biking Bicycling in TrafficFit Changing Components or Adding AccessoriesSaddle position Standover heightHandlebar height and angle Brakes TechBrake reach Hand Brakes How hand brakes work Adjusting your coaster brakeMechanical Safety Check, have your dealer check the brakes Removing a Bolt‑On Front Wheel Wheels Front Wheel Secondary Retention DevicesRemoving a Bolt‑On Rear Wheel with Hand Brake Installing a Bolt‑On Front WheelInstalling a Bolt‑On Rear Wheel with Hand Brake Pedals Installing a Bolt‑On Rear Wheel with Coaster BrakeRemoving a Bolt‑On Rear Wheel with Coaster Brake Page Page Tire Valves ServiceBefore every ride Mechanical Safety Check Service IntervalsIf your bicycle sustains an impact Lessons Appendix aDriveway Rideout Turning Without WarningSummary Following the LeaderAppendix B Page Appendix C Installing a Quick Release Front Wheel Removing a Quick Release Rear Wheel Seatpost Quick Release Raleigh America, Inc. Bicycle Limited Warranty

2008-2005 specifications

The Diamondback 2008-2005 models highlight a commitment to innovation and performance in the world of bicycles. A fusion of advanced technology and user-friendly features, these bikes cater to a range of riding styles and preferences, making them a popular choice among cycling enthusiasts.

One of the standout features of the Diamondback series during this period is its focus on frame design. The bikes are constructed with high-quality aluminum and steel, ensuring durability while keeping the weight manageable for various terrains. The geometry of these frames is engineered for optimal performance, offering a balanced ride that's both responsive and stable, whether on the road or rugged trails.

In terms of technology, Diamondback has integrated cutting-edge components into their bicycles. The series includes a variety of gear options, featuring reliable Shimano and SRAM components that enhance the shifting experience. This ensures that riders can easily tackle inclines or accelerate speed on flat terrains without missing a beat. Additionally, the inclusion of hydraulic disc brakes provides superior stopping power, enhancing safety and control in all conditions, especially during wet weather.

The suspension systems featured in Diamondback bikes from 2008-2005 are another highlight. The models often utilize a combination of front suspension forks, and in some cases, full suspension setups, that effectively absorb shocks and bumps from rough terrain. This technology allows riders to maintain traction and comfort, making rides smoother and more enjoyable.

Tire selection and design also play a critical role in the performance of these bikes. Diamondback bikes are fitted with high-quality tires that provide excellent grip and traction, allowing cyclists to navigate through various surfaces, from muddy paths to city streets. The tread patterns are optimized for stability, ensuring that riders can confidently tackle corners and uneven ground.

Finally, a variety of model options in the Diamondback 2008-2005 range ensure that cyclists of all skill levels can find a suitable bike. Whether looking for a lightweight road bike for speed, a versatile hybrid for commuting, or a rugged mountain bike for adventurous trails, Diamondback has catered to diverse needs, ensuring a bike for every rider.

In conclusion, the Diamondback 2008-2005 models stand out for their superior construction, advanced technology, and thoughtful design. These bicycles represent a harmonious blend of performance, comfort, and versatility, making them a reliable choice for anyone passionate about cycling.
Top Page Image Contents