INSTRUCTIONS
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF
THIS OWNERS MANUAL
1.Remove all contents from underside of tank. Keep tank (1) bottom side up. Install wheel axle (2) through wheel carriage (67) and install wheels
(3) onto wheel axle (2) with spacers (69) as shown. Secure wheel bracket as shown, a deep socket is recommended.
IMPORTANT! DO NOT OVER TIGHTEN.
2.Correctly identify each pole section and mark indicated distance from ends with tape as shown.
3.Align pole top and middle pole sections as shown using alignment mark and hole.
IMPORTANT! Holes in top (4) and middle pole (5) sections MUST align to correctly position elevator system toward playing surface. Bounce pole top (4) and middle section (5) together as shown until they no longer move toward taped reference mark. NOTE: Pole sections should have a
4.IMPORTANT! Holes in top (4) and bottom pole (6) sections MUST align to correctly position elevator system toward playing surface. Add bottom pole section (6) to assembly as shown using alignment mark and hole, and bounce until completely tight. Once assembled, pole sections CAN NOT be separated! NOTE: Pole sections should have a
5.Install rod (7) through holes in bottom pole section (6) and eyebolt (8).
6.Insert pole assembly into tank assembly as shown. Secure pole assembly with upper pivot bracket (9) and lock nut (10).
7.Secure base struts (11) to pole using bolt (12), washers (13), and nut (14), as shown. Place vinyl bolt cover (46) over exposed bolt threads. Rotate the
8.Secure base struts (11) to base using bolt (16), washers (13), and nut (17).
9.Insert carriage bolts (18) into middle set of holes on wheel bracket (19) as shown.
10.Attach lower pivot bracket (20) to wheel bracket (19) using bolt (21), washers (13), disc (22), and nut (10) as shown.
11.Attach handle bar (23) to wheel bracket assembly using nuts (17) as shown.
12.Install wheels (3) onto axle (24) and wheel bracket assembly with push caps (25) as shown.
13.Attach wheel bracket assembly to base assembly using bolt (26), washers (13), and nut (10) as shown.
14.NOTE: Two people recommended for this step. Carefully reposition entire assembly to upright position.
Attach front of plastic handle (27) to back of plastic handle (28) around handle bar (23) using
IMPORTANT! Front of plastic handle (27) should face outward, away from pole assembly.
15.Insert bolts (30) through plastic handle assembly, handle bar (23) and attach nuts (17) as shown. Tighten completely.
16.Install net clips (21).
The Quick Clip™ rapid release net system lets the net pull away from the rim. This reduces the risk of player injury or property damage. However, improper installation or a ball making contact at an odd angle may disengage the net clip from the goal rim. Usually, the clip is reinstalled with little or no problem. We hope that you agree this inconvenience is minor when compared to the safety of the players. Quick Clip: US Patent No. 5,792,010/5,795,253
The two outer hooks on net clip must face towards inside of goal rim. Insert larger hole in net clip onto rim stud, push down on net clip, then slide net clip right, locking or snapping securely into position (clips must "snap" into place to insure a secure fit).
NOTE: Net clips should not slide with ease. It is very important that the net clips are in the locked position before going on to next step.
WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY.
17.Attach elevator bracket (33) to middle pole section (5) using bolts (34), reinforcement bracket (29), and nuts (17) as shown.
18.Attach backboard support brackets (35) to the backboard frame using bolts (36), spacers (37), and nuts (38) as shown.
19.Attach lower elevator tubes (42) to backboard support brackets (35) using spacers (39), bolt (41), and nut (40) as shown. NOTE: Rim mounting nuts and bolts supplied with rim hardware. NOTE: DO NOT use washers here on spring return style rims.
20.Attach upper elevator tubes (45) to backboard support brackets (35) using spacers (43), bolt (44), and nut (40) as shown.
21.A. Attach upper and lower elevator tubes (45, 42) to upper pole
section (4) using bolts (44, 41) and nuts (40) as shown. Attach pole cap (48) as shown.
B. Attach counterbalance spring (48) to upper elevator tubes (45) with bolt
(49)and nut (14) in location shown. Stretch spring to lower elevator tubes (42) and attach with hardware (50, 10) as shown.
NOTE: Slide counterbalance spring against elevator tubes.
22.Insert locking pin (52) into bracket on adjustment tube (51). Insert cross pin (53) through hole in bracket and locking pin (52) as shown in figure A. Fit left handle (54) onto adjustment tube (51) so the bottom of adjustment tube (51) sits on the two small ribs of the handle as shown in figure B.
23.Insert spring (56) into back of locking pin (52) as shown. Spring (56) should rest between two small ribs at the back of the plastic handle as shown in Figure C. Insert top of trigger (57) into bracket on the adjustment tube (51) as shown. The plastic post of the handle pieces should go through the hole in bottom of trigger (57) and hold it into place as shown.
24.Finish handle assembly by attaching right handle (55) using screws (58) as shown.
25.Attach adjustment tube (51) to lower elevator tubes (42) using bolt (41), spacers (59), and nut (40) as shown.
26.Insert lower adjustment rod (60) into bottom of adjustment tube (51), pull trigger to allow lower adjustment rod (60) to move about
WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY.
WARNING: DO NOT LEAVE ASSEMBLED UNIT UNATTENDED WHEN EMPTY, MAY TIP OVER.
27.Roll the completed assembly to the desired playing area. Insert the
IMPORTANT! Add two gallons (7.6 Liters) of
WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY, MAY TIP OVER.
28.Apply the height adjustment and moving label (64) to the front of the pole as shown.
29.Install net (65).
IMPORTANT! Make sure net is held by all three hooks on the net clip.
A.Slide net into outer hook as shown.
B.Slide net into second outer hook creating a loop as shown. Push loop to back of clip.
C.Pull loop up and through back of clip, snapping over the middle hook.
D.Pull net down to make sure it is held securely by all three hooks. NOTE: If net releases during normal play, net was improperly installed. Please review instructions to install net properly.
30.Lock elevator system into highest position (so the backboard is as high as it will go). Apply 10 ft. height indication sticker (66) to adjustment tube (51) directly below arrow on handle as shown. Move elevator system to the next position and apply the 91/2 ft. sticker. Repeat until all height settings have been labeled.
31.Pull trigger (57). Move elevator system up or down to desired height, release trigger (57) to lock system into one of the five height settings.
WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.
5 | 12/01 P/N 211488E |