Huffy AWLH4030 manual Warranty Card

Page 6

INSTRUCTIONS

IMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL

1.Install wheel axle (2) through wheel carriage (68) and install wheels (3) onto wheel axle (2) with spacers (67) as shown. Secure wheel bracket as shown, a deep socket is recommended.

IMPORTANT! DO NOT OVER TIGHTEN.

2.Correctly identify each pole section and mark indicated distance from ends with tape as shown.

3.IMPORTANT! Holes in top (4) and middle pole (5) sections MUST align to correctly position elevator system toward playing surface. IMPORTANT! Bounce pole top (4) and middle section (5) together as shown until they no longer move toward taped reference mark. Upright assembly. NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap.

4.IMPORTANT! Holes in top (4) and bottom pole (6) sections MUST align to correctly position elevator system toward playing surface. Add bottom pole section (3) to assembly as shown and bounce until completely tight. NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap. Once assembled, pole sections CAN NOT be separated!

5.Install rod (7) through holes in bottom pole section (6) and eyebolt (8).

6.Insert pole assembly into tank assembly as shown. Secure pole assembly with upper pivot bracket (9) and lock nut (10).

7.Secure base struts (11) to pole using bolt (12,) washers (13), and nut (14), as shown.

WARNING: TIGHTEN BOLT (12) IN LOCK NUT (14) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE.

Rotate the non-secured ends of base struts (11) as shown.

8.Secure base struts (11) to base using bolt (16) washers (13) and nut (17).

9.Insert carriage bolts (18) into middle set of holes on wheel bracket (19) as shown.

10.Attach lower pivot bracket (20) to wheel bracket using bolt (21), washers (13), disc (22), and nut (10) as shown.

11.Attach handle bar (23) to wheel bracket assembly using nuts (17) as shown.

12.Install wheels (3) onto axle (24) and wheel bracket assembly with push caps (25) as shown.

13.Attach wheel bracket assembly to base assembly using bolt (26), washers (13), and nut (10) as shown.

14.Carefully reposition entire assembly as shown. NOTE: Two people recommended for this step.

15.Attach front of plastic handle (27) to back of plastic handle (28) around handle bar (23) using self- tapping screws (29) as shown.

IMPORTANT! Front of plastic handle (27) should face outward, away from pole assembly.

16.Insert bolts (30) through plastic handle assembly, handle bar (23), and attach nuts (17) as shown. Tighten completely.

17.Attach elevator bracket (38) to middle pole section (5) using bolts (39) and nuts (17) as shown.

18.Assemble board brackets (40) using spacers (44) bolts (45, 46) and nuts (47, 48) as shown.

19.Attach lower elevator tubes (52) to backboard brackets (40) using spacers (49) bolt (51) and nut (50) as shown.

20.Bend top of backboard brackets (40) outward to match up with holes on the backboard and secure using nuts (17) and bolts (43) as shown. Attach rim (32) to backboard using using bolts (42) and nuts (17) as shown.

NOTE: DO NOT use washers here on spring return style rims.

21.Attach upper elevator tubes (55) to backboard brackets (40) using spacers (53) bolt (54) and nut (50) as shown.

22.Attach upper and lower elevator tubes (55, 52) to upper pole section (4) using bolts (51, 54) spacers (67) and nuts (50) as shown. Attach pole cap (33) as shown.

23.Insert locking pin (57) into bracket on adjustment rod (60). Insert cross pin (56) through hole in bracket and locking pin (57) as shown in figure A. Fit left handle (58) onto adjustment rod (60) so that the bottom of adjustment rod (60) sits on the two small ribs as shown in figure B.

24.Insert spring (61) into back of locking pin (57) as shown. Spring (61) should rest between two small ribs on back of plastic handle as shown in Figure C. Insert top of trigger (66) into bracket on adjustment rod (60) as shown. Plastic post on handle pieces should go through hole in bottom of trigger (66) and hold it into place as shown.

25.Finish handle assembly by attaching right handle (59) using screws (29) as shown.

26.Attach adjustment rod (60) to lower elevator tubes (52) using bolt (51) spacers (62) and nut (50) as shown.

27.Insert lower adjustment tube (63) into bottom of adjustment rod (60), pull trigger to allow lower adjustment tube to move about mid-way into adjustment rod (60), release trigger so that lower adjustment tube (63) locks into position midway inside adjustment rod (60). Attach lower adjustment tube (63) to elevator bracket (38) using bolt (64) and nut (14) as shown.

WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY.

WARNING: DO NOT LEAVE ASSEMBLED UNIT UNATTENDED WHEN EMPTY, MAY TIP OVER.

28.Roll completed assembly to desired playing area. Secure assembly to ground using T-Strap (15) and tie down stake (34). Fill tank with 30 gallons of water.

IMPORTANT! Add two gallons (7.6 Liters) of non-toxic antifreeze in sub-freezing climates.

WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY, MAY TIP OVER.

29.Apply height adjustment and moving label (36) to front of pole as shown.

30.Lock elevator system into highest position (so that backboard is as high as it will go). Apply 10 ft. height indication sticker (65) to adjustment tube

(63)directly below arrow on handle as shown. Move elevator system to the next position and apply the 91/2 ft. sticker. Repeat until all height settings have been labeled (8-10ft.).

31.Pull trigger (66). Move elevator system up or down to desired height, release trigger (66) to lock system into one of the five height settings.

WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.

WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY.

32.Install net clips as shown. (See illustration)

33.Install net as shown. (See illustration)

WARRANTY CARD:

Please remember to complete your product registration form either on-line at: www.huffysports.com/warrantycard or mail-in the enclosed postcard.

P/N 214945B

05/03

6

Image 6
Contents Safety Instructions Before YOU Start Hardware Identifier Hardware Identifier Parts List See Hardware Identifier Warranty Card 05/03 214945B TOP Middle Bottom 05/03 214945B See Text 05/03 214945B 214945B 05/03 For spring loaded rim See Text Fig. a Fig. C 05/03 214945B Height Adjustment Stickers Clip ARM Bras DE LA Pince CLIP-ARM Brazo DEL Sujetador Side View Equipement de basketball portable Manuel de lutilisateur 214945B 05/03 05/03 214945B Advertencia 05/03 214945B 214945B 05/03 Warnung 214945B 05/03 Sechskantkopfschraube, Gelb Dichromate, 5/16-18 x 3,60 Länge