Vector VEC1198POB Operating the Lantern, Operating the AM/FM Radio, Operating the Weather Radio

Page 5

VEC1198POB_Manual_022406 2/24/06 5:21 PM Page 4

Using the Dynamo Hand-Crank

Collapse the Hanging Hook and Handle to release the hand-crank and press it against the unit’s body to secure into position. Rotate the Dynamo Hand-Crank handle clockwise (at a rate of approximately 1.6 rotations per second) to generate power if back-up battery power is low. Turn off all functions while recharging using this method for best results.

Using Battery Power

The VEC1198POB comes with a 12 Volt DC Detachable Battery Pack that can power all of the unit’s features. When the Removable Battery will no longer hold a charge, it can be replaced. See “Battery Replacement/ Disposal” on page 5.

Note: When the battery is inserted into the unit and the AC plug pin is inserted into the charging port, (even if the cube is not plugged in) the Removable Battery will charge the Internal Backup System Battery.

OPERATING THE LANTERN

The Lantern is controlled by the Lantern ON/OFF Pushbutton on the back of the unit (see the “Control and Function Guide” on page 2).

Note: When the 12 Volt DC detachable Battery Pack power runs low and alternate 12 Volt DC power cord use is unavailable, the tube Lantern will power off. The Radio and LED Backup Lights will continue to operate as long as Hand Crank backup battery source is utilized.

OPERATING THE AM/FM RADIO

See the “Control and Function Guide” on page 2 to locate referenced controls, knobs and selectors.

Slide the AM/FM/WX Selector to the desired frequency (the AM or FM position).

Turn the Radio Tuner Knob to select the desired station.

Extend the built-in Radio Antenna and adjust for best reception.

Adjust the volume using the Volume Control Knob.

To turn the Radio OFF, simply slide the AM/FM/WX Selector to the OFF position.

OPERATING THE WEATHER RADIO

Slide the AM/FM/WX Selector to the WX (Weather Band) position.

With the ALERT ON/OFF Pushbutton OFF, turn the Radio Tuner Knob to select the NOAA station with the strongest signal.

Extend the built-in Radio Antenna and adjust for best reception.

Adjust the volume using the Volume Control Knob.

Press the Alert Pushbutton to turn the Alert feature ON (the Alert LED will light) and press the ALARM/LOCK Pushbutton to set it in LOCK position (the Alarm Lock LED will light) for Alert standby mode. Note that the speaker is muted while Radio monitors for a hazard alert.

To turn the Radio OFF, simply slide the AM/FM/WX Selector to the OFF position.

Notes: While in ALERT mode, the hazard alarm will sound briefly when a hazard alert is received. While in the LOCK position, the alarm SOUNDS CONTINUOUSLY WHEN THE HAZARD ALERT IS RECEIVED UNTIL THE USER TURNS IT OFF.

For the Lock Function to be available, ALERT must be engaged.

4

OPERATING THE LED BACKUP LIGHT

The LED Backup Light in the lantern base is controlled by the LED Light ON/OFF Pushbutton on the back of the unit. (See the “Control and Function Guide” on page 2.)

USING THE 12 VOLT DC PORTABLE POWER SUPPLY

This portable power source is also for use with 12 volt DC accessories equipped with a male accessory outlet plug that are rated up to 1 amp (generally, a cell phone charger).

1.Lift up the cover of the unit ‘s 12 volt DC outlet.

2.Insert the 12 volt DC plug from the appliance into the 12 Volt DC Accessory Outlet on the side of the unit (see the “Control and Function Guide” on page 2).

DO NOT EXCEED A 1 AMP LOAD.

3.Switch on the appliance and operate as usual.

4.Periodically press the battery charge level pushbutton to check battery status.

CARE AND MAINTENANCE

Cleaning

Over time, dust or fingerprints may accummulate on the Lantern glass. Clean with a soft, clean, oil-free cloth moistened with household window cleaner. Do not use alcohol based cleaners on plastic surfaces. This will eventually cause surface clouding.

Note: Never submerge this unit in water or any other liquid.

Replacement Parts

Check unit periodically and discontinue use if parts or accessories are found to be damaged or defective. To replace worn or defective parts, contact Vector Customer Service toll-free at (866) 584-5504.

12 Volt DC Adapter Plug Fuse Replacement

The fuse in the DC plug protects the charging circuit of the 12 Volt DC Adapter. If AC powering/recharging works, but DC powering/recharging does not, then the fuse may be opened (blown).

To replace the fuse:

1.Unscrew the gold end cap of the DC plug (counterclockwise).

2.Remove spring center contact and fuse.

3.Check fuse with a continuity checker.

4.If blown, locate replacement fuse with same type and rating.

5.Replace the fuse, spring, contact and end cap.

6.Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.

7.Test for proper operation of the 12 Volt DC Adapter.

5

Image 5
Contents ONE Year Limited Warranty Program Important Safety INFORMATION, Save These InstructionsImportant Safety Instructions Table of Contents Using the 120 Volt AC Adapter Power SupplyUsing the 12 Volt DC Adapter Control and Function GuideUsing the 12 Volt DC Portable Power Supply Operating the LED Backup LightCare and Maintenance Operating the LanternSpecifications Bulb ReplacementBattery Replacement/Disposal

VEC1198POB specifications

The Vector VEC1198POB is a portable power inverter that stands out in the vast market of power delivery systems. Designed with versatility and convenience in mind, this product showcases a robust set of features tailored to meet the needs of both casual users and professionals.

One of the standout characteristics of the VEC1198POB is its powerful 2000-watt continuous output with a peak surge capability of 4000 watts. This allows users to power a variety of devices simultaneously, making it ideal for camping, road trips, and emergency power outages. The inverter is equipped with two AC outlets, allowing for the connection of multiple appliances without compromising performance.

The VEC1198POB supports a wide input voltage range, making it compatible with both 12V and 24V battery systems. This flexibility ensures that users can easily integrate the inverter into their existing setups, whether for recreational vehicles, boats, or even household emergency backup.

In terms of safety, the Vector VEC1198POB excels with built-in protections against over-temperature, over-voltage, low-voltage, and short circuits. These features help prevent damage to both the inverter and connected devices, providing peace of mind to users during operation. The inverter's quiet operation, combined with its efficient design, ensures that it can be used in a variety of settings without causing distractions or disturbances.

Another significant feature of the VEC1198POB is its friendly user interface. The LED indicators provide real-time status updates on output levels, battery condition, and any potential faults, making it easy for users to monitor performance.

Lightweight yet sturdy, the Vector VEC1198POB is designed for portability, enabling users to transport it effortlessly. The compact design also allows for easy storage when not in use, making it suitable for both home and outdoor applications.

In summary, the Vector VEC1198POB combines impressive power output, compatibility with various battery systems, safety features, and portability, making it an essential tool for anyone seeking reliable power on the go or during emergencies. Whether for recreational use or as a backup power source, the VEC1198POB proves to be a valuable asset in any power management toolkit.