Hotpoint AQM8D 69 I instruction manual 65 100 cm

Page 3

Connecting the drain hose

• the supply voltage is included within the values indica-

EN

ted on the Technical Data Plate fixed on the machine;

65 - 100 cm

Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor;

the socket is compatible with the washing machine’s plug.

If this is not the case, replace the socket or the plug.

Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED. THE FOLLOWING OPERATIONS SHOULD BE CARRIED

Where it connects to the waste water pipe cut end off spigot or remove the blanking cap

The drain hose may be connected to an under-sink trap. Before connecting the drain hose from the machine ensure that any blanks or removable ends have been taken off the spigot.

If it is placed over the edge of a basin or sink be sure the free end of the hose should not be underwater.

OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug and you should wish to re-route the mains cable through partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere rewireable plug bearing the BSI mark of approval.

or:

!We advise against the use of hose extensions; in case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

Ensure that if the drain hose is pushed into a standpipe, that the end does not go down more than 15cms (6 inches). If the hose is pushed down too far, this may cause the machine to self -syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains socket, make sure that:

the socket is earthed and in compliance with the applicable law;

the socket is able to sustain the appliance’s

maximum power load indicated in the Technical details table (see page 5);

the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in compliance with BS 5733) which is accessible without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be accidentally inserted into a socket.

Instructions for connecting cable to an alternative plug: Important: the wires in the mains lead are coloured in accordance with the following code:

Green & Yellow Earth

BlueNeutral

Brown Live

3

Image 3
Contents Aqualtis Instructions for installation and useInstallation Connecting the electricity and water suppliesUnpacking and levelling 65 100 cm With the following code How to connect an alternative plugColoured Green or Green & Yellow Amp fuse, either in the plug or adaptor or atTechnical data Always use the handle to open the porthole door see figure Description of the machineSTART/PAUSE button Touch control panelM2 M1 Selector knobHow to run a wash cycle or a drying cycle Time Saver Wash cycles and optionsTable of wash cycles Wash optionsWashing recommendations Detergents and laundryEN Detergent Preparing the laundryOpening the porthole door manually Precautions and tipsGeneral safety DisposalCare and maintenance Trouble shooting Problem Possible causes / SolutionsMachine is trapped between cabinets and/or walls Machine wont spin properly Machine leaks from the dispenser Assistance Guarantee195076572.05 After Sales Service