Hotpoint V3D01 manual Electrical Requirements

Page 5

Electrical Requirements

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING: This appliance must be earthed!

 

 

 

 

 

 

 

 

 

 

 

Supply

 

 

REFER TO THE RATING PLATE FOR VOLTAGE AND CURRENT

 

 

 

 

 

 

 

REQUIREMENTS. (see diagram for location.)

 

 

 

 

 

 

 

The flexible mains lead is supplied fitted with a BS1363 plug and

 

 

 

 

 

 

 

with a 13 amp BS1362 fuse.

 

 

 

 

 

 

 

The plug should be connected to the mains supply via a suitable

 

 

 

 

 

 

 

switched socket which is accessible after installing your dryer.

 

 

 

 

 

 

Changing

 

 

If it is necessary to fit a replacement fuse, it must be a 13 amp

 

the fuse

 

 

ASTA approved to BS1362 type.

 

Moulded plug

 

 

 

 

WARNING: The plug must not be used without a fuse cover.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If a replacement fuse holder/cover is required, it must be of the

 

 

 

 

 

 

 

same colour coding or wording as shown on the base of the plug.

 

 

 

 

 

 

 

Replacements are available from your Spares stockist.

 

 

 

 

 

 

Changing

 

 

The wires in the mains lead are coloured in accordance with the

 

the plug

 

 

following:

 

 

 

 

 

 

 

 

 

GREEN/YELLOW - EARTH

 

 

 

 

 

 

 

BLUE

- NEUTRAL

 

 

 

 

 

 

 

BROWN

- LIVE

 

Rewirable plug

 

If a replacement plug is to be fitted, the appropriate wire must be

 

 

 

 

 

 

 

connected to the correct terminal,as follows:

 

GREEN &

 

 

 

 

 

 

 

 

 

 

 

 

 

YELLOW TO

 

 

 

 

 

 

 

 

EARTH

 

 

 

 

Connect:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Green/Yellow to terminal marked Earth or Green or

 

 

 

 

 

 

 

Blue to terminal marked Neutral or N or Black

 

 

 

 

 

 

 

Brown to terminal marked Live or L or Red.

 

 

 

 

 

13 AMP

 

 

 

 

 

 

FUSE

 

If the plug being replaced is a non-rewirable type then the cut-off

 

 

 

 

 

 

 

plug must be disposed of safely. DO NOT leave where it can be

 

 

 

 

 

BROWN

 

 

 

 

 

 

 

 

BLUE TO

 

 

 

TO LIVE

 

inserted into a socket and create a shock hazard.

 

NEUTRAL

 

CORD

 

 

 

 

 

 

 

 

CLAMP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Changing the

 

Should the mains lead ever require replacing at any time please

 

mains cable

 

 

contact your nearest Service Centre. A charge will be made for the

 

 

 

 

 

 

 

replacement of the mains lead or if you require a longer lead.

 

 

 

 

 

 

 

The mains lead must only be replaced by a specially prepared

 

 

 

 

 

 

 

cable obtainable from your Spares Stockist and fitted by a

 

 

 

 

 

 

 

qualified electrician.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: IF IN DOUBT ABOUT ANY OF THE ABOVE CONSULT A

 

 

 

 

 

 

 

QUALIFIED ELECTRICIAN.

 

 

 

 

 

 

 

 

 

 

5

Image 5
Contents Instructions for Installation and Use Contents For your safety Symbol Ventilation. see, Where to put and vent your dryerBuy genuine accessories and spares Close the doorElectrical Requirements Where to put and vent your dryer How to use your dryer Maximum load size Typical load Sorting your laundryItems not suitable for tumble drying Wash Care LabelsItems requiring special attention Door Release Heat Selection Mains Light if fitted Never wind the Timer Control anti-clockwiseControls Guide to Drying Times Switch off electricity and remove plug When finished After each load As necessary LubricationCaring for your Dryer To remove the filterProblem Problem Check these things firstIf something goes wrong ‘It is taking a long time to dry’If it still won’t work Key Contacts
Related manuals
Manual 20 pages 33.09 Kb