Hotpoint HY6F3551 manual Replacing the fuse

Page 3

Connecting the drain hose

• the supply voltage is included within the

GB

values indicated on the Technical Data Plate

 

65 - 100 cm

Connect the drain hose, without bending it, to a draining duct or a wall drain situa- ted between 65 and 100 cm from the floor;

fixed on the machine.

the socket is compatible with the washing machine’s plug. If this is not the case, repla- ce the socket or the plug.

Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

Where it connects to the waste water pipe cut end off spigot or remove the blanking cap

The drain hose may be connected to an under-sink trap. Be- fore connecting the drain hose from the machine ensure that any blanks or remo- vable ends have been taken off the spigot.

If it is placed over the edge of a basin or sink be sure the free end of the hose should not be under- water.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRI- CIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the colou- red marking or the colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your nearest Service Depot.

Removing the plug:

!We advise against the use of hose extensions; in case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

Ensure that if the drain hose is pushed into a standpipe, that the end does not go down more than 15cms (6 inches). If the hose is pu- shed down too far, this may cause the machine to self -syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains socket, make sure that:

the socket is earthed and in compliance with the applicable law;

the socket is able to sustain the appliance’s maximum power load indicated on the Tech- nical Data Plate fixed on the machine;

If your appliance has a non-rewireable moul- ded plug and you should wish to re-route the mains cable through partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere rewireable plug bearing the BSI mark of ap- proval.

or:

the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in compliance with BS 5733) which is accessible without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be accidentally inserted into a socket.

Instructions for connecting cable to an alternati- ve plug:

Important: the wires in the mains lead are co- loured in accordance with the following code:

Green & Yellow Earth

BlueNeutral

Brown Live

3

Image 3
Contents Instructions for use ContentsElectric and water connections Unpacking and levellingReplacing the fuse Disposing of the appliance First wash cycleMPa 0.5 bar Technical dataMinimum pressure NectionsCare and maintenance Disposal Precautions and tipsGeneral safety This appliance can be used by children agedControl panel Description of the washing machine and starting a wash cycleStarting a wash cycle Indicator lightsTable of wash cycles Wash cyclesFunctions Setting the temperatureSetting the spin speed PersonalisationGarments requiring special care Detergents and laundryDetergent dispenser drawer Preparing the laundryProblem Possible causes / Solutions TroubleshootingPage Assistance GuaranteeGB195109171.00 After Sales Service