Whirlpool WGD9750W dimensions Duet Steam and Non-Steam Electronic Gas Dryer, Overall Dimensions

DuetSteam and Non-Steam Electronic Gas Dryer

PRODUCT MODEL NUMBERS

WGD9450W, WGD9470W, WGD9550W, WGD9600T, WGD9750W, WGD9610X

Gas supply: This dryer is equipped for use with Natural gas. Dryer can be converted to L.P. gas. When rigid pipe is used it should be 1/2" IPS. When acceptable to the gas supplier and local codes, 3/8" approved tubing may be used for lengths under 20 ft (6.1 m). For lengths over 20 ft (6.1 m), larger tubing should be used. Pipe-joint compounds resistant to the action of L.P. gas must be used. An individual manual shutoff valve must be installed within 6 ft (1.8 m) of the dryer in accordance with the National Fuel Gas Code ANSI Z223.1.

Electrical: A 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply is required for gas dryers, 30 amp for electric dryers. A time-delay fuse or circuit breaker and a separate circuit are recommended.

Water (Steam models only): The dryer must be connected to the cold water faucet using new inlet hoses. Do not use old hoses. Do not overtighten.

OVERALL DIMENSIONS

Dryer dimensions	STEAM - 529/16"	Custom undercounter installation-dryer only
	(1335 mm)
	NON-STEAM - 511/2"
	(1308 mm)	38"
		(965 mm)
38"		1"*	27"	1"*
(965 mm)
		(25 mm)	(686 mm)	(25 mm)
		Most installations require a minimum
		5" (127 mm) clearance behind the dryer for
*STEAM - 329/16"	27"	the exhaust vent with elbow. See Installation
		Instructions, “Venting Requirements.”
(827 mm)	(686 mm)
†NON-STEAM - 311/2"
(800 mm)

For closet installation, with a door, the minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent air

ventilation openings are acceptable.

Damage to the coupling can result.

Exhaust venting: Exhaust your dryer to the outside. 4" (102 mm) diameter vent is required. Rigid or flexible metal exhaust vent must be used. Do not use plastic or metal foil vet. Exhaust hood must be at least

12" (305 mm) from the ground or any object that may be in the path of the exhaust.

Hood styles: A & B are recommended.

B	4"	C
	(102 mm)
A
		2½"
4"		(64 mm)
	A. Louvered hood
(102 mm)
4"	B. Box hood
	C. Angled hood (acceptable)

48in.2 * (310 cm2)

24in.2 * (155 cm2)

3"
(76 mm)	14" max.
	(356 mm)
	18" max.
	(457 mm)
3"
(76 mm)
	STEAM - 329/16"
	(827 mm)
NON-STEAM - 311/2"
	(800 mm)

	6"
	(152 mm)
	76"
	(1930 mm)
	1"
STEAM - 51/2"**	(25 mm)
(140 mm)
NON-STEAM - 5"**
(127 mm)

27" (686 mm)

1" (25 mm)

(102 mm)

The vent system chart provides venting requirments that will help to achieve the best drying performance.

For dryer on pedestal; cabinet installation, with a door, the minimum ventilation openings in the top are required.

Vent system chart:

NOTE: Side and bottom exhaust installations have a 90° turn inside the dryer. To determine maximum exhaust length, add one 90° turn to the chart.

Number of	Type of	Box or	Angled
90o turns	vent	Louvered	hoods
or elbows		hoods
0	Rigid metal	64 ft (20 m)	58 ft (17.7 m)
1	Rigid metal	54 ft (16.5 m)	48 ft (14.6 m)
2	Rigid metal	44 ft (13.4 m)	38 ft (11.6 m)
3	Rigid metal	35 ft (10.7 m)	29 ft (8.8 m)
4	Rigid metal	27 ft (8.2 m)	21 ft (6.4 m)

7"*

(178 mm)

14"* max.

(356 mm)

18"* max.

(457 mm)

STEAM - 329/16"

(827 mm)

NON-STEAM - 311/2"

(800 mm)

7"*

(178 mm)

9"* (229 mm)

		1"*				1"*
				27"
5"	(25 mm)		(686 mm)		(25 mm)

(127 mm)

	37/16"		33/8"
1"	(87 mm)	1"	(86 mm
(25 mm)		(25 mm)
	14"		75/8"
	(356 mm)		(194 mm)
	Back View		Side View

*Required spacing **For side or bottom venting, 0" (0 mm) spacing is allowed.

Select the route that will provide the straightest and most direct path outdoors. Plan the installation to use the fewest number of elbows and turns.

Use the fewest 90° turns possible.

Do not use vent runs longer than specified in vent length chart. Determine the number of elbows you will need.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation	W10255469B
Instructions packed with product. Specifications subject to change without notice.	06/2011