Whirlpool 8578185 manual Plan Vent System, Optional exhaust installations

Page 14

The angled hood style (shown here) is acceptable.

4"

(10.2 cm)

2½" (6.4 cm)

An exhaust hood should cap the vent to keep rodents and insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

Do not use an exhaust hood with a magnetic latch.

Improper venting can cause moisture and lint to collect indoors, which may result in:

Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc.

Housecleaning problems and health problems.

Plan Vent System

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer. Other installations are possible.

 

B

 

C

 

D

A

E

 

F

 

G

 

H

A.Dryer

B.Elbow

C.Wall

D.Exhaust hood

E.Clamps

F. Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet

Optional exhaust installations

This dryer can be converted to exhaust out the right side, left side, or through the bottom. Contact your local dealer to have the dryer converted.

WARNING

Fire Hazard

Cover unused exhaust holes with one of the following kits:

279818 (white)

279925 (biscuit)

279969 (pewter)

Contact your local dealer.

Failure to follow these instructions can result in death, fire, electrical shock, or serious injury.

ABC

A. Standard rear offset exhaust installation B. Left or right side exhaust installation

C. Bottom exhaust installation (not an option with pedestal installations)

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer’s instructions.

AB

A. Over-the-top installation (also available with one offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the “Assistance or Service” section of this manual to order.

Over-the-Top Installation: Part Number 4396028

14

Image 14
Contents Electronic Electric Dryer 8578185Table of Contents Dryer Safety Your safety and the safety of others are very importantOptions Installation InstructionsTools and Parts Location Requirements Installation clearancesDryer Dimensions You will needMobile home installations require Minimum installation spacing for cabinet installationMobile home Additional installation requirements Recessed or closet installation Dryer on pedestalElectrical Connection Electrical RequirementsIt is your responsibility Electrical Connection Power Supply Cord Direct WireStyle 1 Power supply cord strain relief Wire connection Power supply cord Style 2 Direct wire strain reliefWire connection Direct wire Remove center silver-colored terminal block screwBDE CG F Optional 3-wire connection If this is a new vent system Vent material If using an existing vent systemVenting Requirements Plan Vent System Optional exhaust installationsAlternate installations for close clearances Vent system chart Install Vent SystemSpecial provisions for mobile home installations Determine vent pathLevel Dryer Install Leveling LegsComplete Installation Connect VentTo use an Automatic Cycle Dryer USEStarting Your Dryer Control Locked Pausing or RestartingStopping Your Dryer Drying and Cycle TipsStatus Lights CyclesAdditional Features End of Cycle Signal Drying RackCleaning the Dryer Interior Cleaning the Dryer LocationCleaning the Lint Screen Dryer CareVacation and Moving Care Changing the Drum LightTroubleshooting Dryer OperationStains on load or drum Cycle time too shortLint on load Loads are wrinkledFor assistance and service Assistance or ServiceIf you need replacement parts Accessories U.S.APage Whirlpool Corporation Major Appliance Warranty 8578185