Install VentSystem, Install LevelingLegs

Determine vent length and elbows needed for best drying performance

■Use the following Vent system chart to determine type of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those specified will:

■Shorten the life of the dryer.

■Reduce performance, resulting in longer drying times and increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90º turn inside the dryer. To determine maximum exhaust length, add one 90º turn to the chart.

Number of	Type of	Box or	Angled
90º turns	vent	louvered	hoods
or elbows		hoods

0	Rigid metal	64 ft (20 m)	58 ft (17.7 m)
	Flexible metal	36 ft (11 m)	28 ft (8.5 m)

1	Rigid metal	54 ft (16.5 m)	48 ft (14.6 m)
	Flexible metal	31 ft (9.4 m)	23 ft (7 m)

2	Rigid metal	44 ft (13.4 m)	38 ft (11.6 m)
	Flexible metal	27 ft (8.2 m)	19 ft (5.8 m)

3	Rigid metal	35 ft (10.7 m)	29 ft (8.8 m)
	Flexible metal	25 ft (7.6 m)	17 ft (5.2 m)

4	Rigid metal	27 ft (8.2 m)	21 ft (6.4 m)
	Flexible metal	23 ft (7 m)	15 ft (4.6 m)

Install VentSystem

1.Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.

2.Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3.Run vent to dryer location. Use the straightest path possible. See “Determine vent path” in “Plan Vent System.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior of the vent to secure vent.

Install LevelingLegs

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

1.To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.

2.Firmly grasp the body of the dryer (not the console panel). Gently lay the dryer on the cardboard. See illustration.

3.Examine the leveling legs. Find the diamond marking.

4.Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible.

5.Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent.

ConnectVent

1.Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (10.2 cm) clamp.

2.Move dryer into its final location. Do not crush or kink vent.

3.(On gas models) Make sure that there are no kinks in the flexible gas line.

4.Once the exhaust vent connection is made, remove the corner posts and cardboard.

8578901 specifications

The Whirlpool 8578901 is a vital component in many households as a replacement part designed for Whirlpool washing machines. This specific part is known for its reliability and compatibility with various Whirlpool models, making it a sought-after choice for homeowners seeking to maintain the efficiency and performance of their washing appliances.

One of the primary features of the Whirlpool 8578901 is its robust construction. It is made from high-quality materials that ensure durability and long-lasting use. This means users can expect consistent performance over time without worrying about premature wear and tear. The component is designed to endure the rigorous demands of regular laundry use, providing peace of mind to consumers who rely on their washers for daily cleaning needs.

In terms of technology, the Whirlpool 8578901 incorporates advanced engineering that enables it to perform effectively within the washing machine's system. The part features a precise design that ensures seamless integration with other machine components. This compatibility helps to maintain optimal performance levels, preventing issues such as leaks or malfunctions that can disrupt laundry routines.

Another characteristic that stands out is the ease of installation. The Whirlpool 8578901 is designed for straightforward replacement processes, allowing users to easily replace worn-out or damaged parts without the need for professional assistance. This feature not only saves on repair costs but also empowers homeowners to take control of their appliance maintenance.

Additionally, the Whirlpool 8578901 offers excellent efficiency. By ensuring that the washing machine operates at its best, this part can contribute to lower energy consumption and water usage. Users can enjoy the benefits of a cleaner wash without incurring high utility bills, making it an environmentally friendly choice.

Moreover, the versatility of the Whirlpool 8578901 is noteworthy. It is compatible with multiple models, which expands its usability across a wide range of Whirlpool washing machines. This universality makes it an ideal solution for many consumers looking to maintain their appliances without needing to search for model-specific parts.

In summary, the Whirlpool 8578901 is a formidable replacement part characterized by its durability, advanced technology, ease of installation, efficiency, and versatility. For anyone looking to ensure their Whirlpool washing machine continues to operate optimally, investing in this part is a wise choice that reflects both practicality and quality.