Important safety instructions

Job: Ion 441375253 Rev 3 -- Color: Composite -- Signature 1, Sheet 1, Back -- Plate 2

The use of any electrical appliance requires the following common sense safety rules.

Primarily there is danger of injury or death and secondly the danger of damage to the appliance. These are indicated in the text by the following two conventions:

WARNING: Danger to the person!

IMPORTANT: Damage to the appliance! In addition we offer the following safety advice.

Location

• Do not use outdoors.

Children

•Children do not understand the dangers associated with operating electrical appliances. Never allow children to use this appliance.

•Close supervision is necessary when any appliance is used near children.

Other safety considerations

•Use the iron only for its intended use.

•To protect against the risk of electric shock do not put the appliance in water or in any other liquid.

•Always disconnect the iron from the electrical socket when filling with water or emptying, and when not in use.

•Do not operate the iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron, but telephone Morphy Richards for advice. Incorrect reassembly can cause a risk of electric shock when the iron is used.

Anti-scale models only

• Keep the anti-scale sachet out of reach

of children.

• Wipe up spilt anti-scale granules

immediately.

• If the granules come into accidental

contact with the eyes, flush them with

water for at least 15 minutes and remove

all particles. Consult a physician if

irritation persists.

• If the granules come into contact with

Emptying and storing

When you have finished ironing, unplug your iron. Ensure that the variable steam control is set at the

‘ ’ position, lift up the fill cap and empty any remaining water out of the filling hole.

Do not store in the box, but in an upright position, so that any drops of water remaining cannot leak out and discolour the soleplate.

Important: The flex can be damaged if wound too tightly around the iron after use. Make a loose loop with the flex and

wrap it around the iron. The iron must be cool before

winding the flex and storing on its heel.

To clean a stainless steel or anodised soleplate (certain models only)

To keep the soleplate of your iron clean and free of limescale, we recommend that you use one of the gentle chrome, silver or stainless steel cleaners that are generally available. Always follow the manufacturers instructions. To clean off melted man-made fibres set the iron at 3 dot position and pass it over a clean piece of cotton which will draw the deposit off the surface.

To clean a coated soleplate (certain models only)

In the unlikely event of any man-made fibre fusing to the soleplate, set the iron at the 3 dot position and pass it over a clean piece of cotton which will draw the deposit off the surface.

Do not use scouring powder or solution as this could cause damage to the coating.

To clean the exterior

Allow the iron to cool and wipe over with a damp cloth and mild detergent, then wipe with a dry cloth.

Personal safety

the skin, remove particles and wash with

water.

• Do not remove the anti-scale cartridge

MaintenanceHelpline

•Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down, there may be hot water in the water tank.

•Do not use the vertical steam feature on clothes that are being worn.

•Do not leave the iron unattended whilst plugged in or on an ironing board. Never allow the mains lead to over hang the work surface.

•The socket should always be off before plugging or unplugging from the socket. Never yank the cord to disconnect from the socket, instead, grasp plug and pull to disconnect.

•Do not allow the cord to touch hot surfaces. Let the iron cool completely before putting away. Loop cord loosely around the iron before storing.

from the iron, unless the tank is empty.

• When filling ensure that the iron is

disconnected from the electrical socket,

and that the cartridge is inserted

correctly.

Special instructions

•If your iron does not work, check the following points:

Has the temperature control been set to the required temperature? Is the plug in its socket? Is the plug itself or the socket faulty? (Check by plugging in another appliance).

Jet cleaning

Your iron has a built in cleaning system designed to keep the water valve, steam chamber and steam vents clear of lint and loose mineral deposits. The ‘jet clean’ should be operated after each period of ironing.

To operate, ensure that there is little water in the tank, place the iron on its heel and turn the temperature control dial to the maximum setting. Wait for the temperature indicator light to go out, then unplug the iron and hold it about 6’’ (150mm) above the sink in the ironing position. Press the shot of steam button about 10 times in succession.

After this cleaning operation, empty out any remaining water.

If you have any difficulty with your appliance, do not hesitate to call us.

We are more likely able to help than the store from where you bought it.

Please have the following information ready to enable our staff to deal with your query quickly.

•Name of the product

•Model number as shown on the underside of the appliance.