IMPORTANT SAFETY INSTRUCTIONS
TROUBLESHOOTING |
When using your iron, basic safety precautions should always be followed, including the following:
1.Read all instructions carefully.
2.Use iron only for its intended use.
3.To protect against risk of electrical shock, do not immerse the iron in water or other liquids.
4.Never yank cord to disconnect from outlet. Grasp plug and pull to disconnect.
5.Do not allow cord to touch hot surfaces. Let iron cool completely before putting away.
6.Always disconnect iron from electrical outlet when filling with water, emptying, or when not in use.
7.Do not operate iron with a damaged cord, or after the iron has been dropped or damaged in any manner. To avoid the risk of electric shock, do not disassemble the iron. Return the iron to
8.Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board.
9.Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down; there may be hot water in the reservoir.
10.Never use or rest iron on an unstable surface.
11.While the iron is hot, never set iron on an unprotected surface - even if it is on its heel rest.
12.CAUTION! TO PREVENT ELECTRIC SHOCK OR OTHER INJURY, before filling the iron with water, make sure that the plug is removed from the outlet.
13.WARNING: Never fill the iron with fabric conditioner, starches or any other solution, as these will damage the steam mechanism. Do not use
contaminated water.
14. CAUTION! TO AVOID FIRE, never leave iron unattended while it is plugged in.
15. CAUTION! TO PREVENT
ELECTRIC SHOCK, never use the iron in a location where it can fall or be pulled into water or another liquid. If the iron falls into water or other liquid, unplug it immediately. DO NOT reach into the water or liquid.
16. WARNING: Never use scouring
pads, abrasive or chemical cleaners, or solvents to clean the exterior or soleplate of your iron. Doing so will scratch and/or damage the surface.
17.CAUTION! DO NOT aim iron at face, towards yourself, or anyone else while using or adjusting steam. Burns or serious injury may occur.
18.Always store your iron standing upright, not on the soleplate. If stored face down, even the smallest amount of moisture will cause the soleplate to corrode and stain.
19.This appliance is for household use only.
SPECIAL INSTRUCTIONS
1.To avoid a circuit overload, do not operate another
2.If an extension cord is absolutely necessary, use a
PROBLEM | POSSIBLE REASONS & SOLUTIONS | |
| • Iron should be plugged into a 120V AC electrical | |
Iron does not heat | outlet only. | |
| Make sure that the plug is securely in the socket. | |
| • Temperature setting too low. | |
| Turn to higher setting. | |
Some odor or small | • This is normal. | |
particles come out of | Follow instructions for first use and allow iron to steam | |
steam vents of new | through | |
iron | occasionally to eliminate small white particles. | |
|
| |
Iron does not steam | • Water tank may be empty or water level is very low. | |
Add water. | ||
| ||
| • Make sure that the fabric/temperature setting and | |
| the variable steam control are correctly set. For | |
| maximum steam, (setting ‘Max’ on steam control), | |
| temperature setting should be set on ‘•••’. | |
| • Variable steam control dial is set on “0”. | |
| Always allow the iron to reach the selected | |
| temperature with the variable steam control setting | |
| at ‘0’. Make sure the temperature setting is set in | |
| the correct steam area, e.g. ‘•’, and the steam control is | |
| not on ‘0’. For more steam, turn temperature dial to | |
| higher setting, e.g. ‘•••’, and the steam control to ‘Max’. | |
| • If temperature setting and steam control setting are | |
| correct and there is no steam, gently tap the | |
| soleplate on the ironing board a few times. Move | |
| the variable steam control from ‘0’ to ‘Max’ a few | |
| times. | |
|
| |
Water droplets coming | • Iron may not be hot enough. Set thermostat to the | |
‘Max’ position. Always allow iron sufficient time to | ||
from steam vents | ||
heat up before activating the variable steam control. | ||
| ||
| • Overuse of steam burst. Allow more time between | |
| each burst. | |
| • Iron may have been overfilled. Turn iron off,empty | |
| water and follow instructions for filling. |
POLARIZED PLUG: This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
SAVE THESE INSTRUCTIONS
For Household Use Only
• Steam performance may be low if iron requires |
seasoning. To season, use regular tap water for 1or 2 |
tanks until steam performance improves. |
1 | Rev. 02/05 | 10 |