Electronic AUTO-OFF, Emptying the Iron | Euro-Pro GI490XH manual

OPERATING INSTRUCTIONS

ELECTRONIC AUTO-OFF

The ELECTRONIC Iron is equipped with an electronic auto-off. The electronic auto-off switches the iron off if it has been left standing unmoved in any position (sideways, flat or upright) for approximately 7-9 minutes. A red light on the LED display panel will flash when the iron switches itself off. (Fig. 8) To switch the iron back on, just shake the iron side- to-side several times.

Flash

Fig. 8

EMPTYING THE IRON

1.Always empty iron after each use.

2.When finished using the iron, turn the variable steam control dial to “0” and press the electronic temperature control button until the power light is lit.

3.Unplug the iron from the electrical outlet.

4.Turn the iron upside down over the sink with the tip pointing downward and allow the water to flow from the opening.

5.Place iron upright and allow to cool before storing.

CAUTION! Use caution when emptying the iron. Burns may

occur from touching hot metal surfaces, hot water or steam.

SELF CLEANING

It is important to “Self Clean” the iron at least every two weeks to remove scale, calcium, etc. The harder the water, the more often the iron should be self cleaned.

1.Set the variable steam control dial to any steam position.

2.Fill the water tank up to the “MAX” level.

3.Stand the iron on its heel. Plug the iron into the electrical outlet.

4.Press the electronic temperature control button until you get the “MAX” temperature setting on the display panel and wait until the iron heats up and temperature setting light stops flashing.

5.Turn the variable steam control dial all the way to the right to the self- cleaning position and hold the iron horizontally over the sink. (Fig. 9).

6.Boiling water and steam will now be ejected from the holes in the soleplate. The impurities and scale are washed away with it.

7.Move the iron back and forth as this happens.

8.If there is any water left in the water tank after the iron stops steaming, just empty the remaining water in a sink following the instructions for emptying the iron.

9.Turn the variable steam control dial to the “0” position when the water tank is empty.

10.Place the iron back upright on its heel to cool down before storing.

Fig. 9

This appliance is for HOUSEHOLD USE ONLY and may be plugged into any 120V AC polarized electrical outlet. Do not use any other type of outlet.

FABRIC & TEMPERATURE INDICATORS

Press on the Electronic Temperature Control to select the desired fabric setting. The red lights at the left of the LED Display Panel will light up.

At the same time, the temperature indicator lights on the right side of the LED Display Panel will start to flash. They will stop flashing when the iron reaches the selected temperature.

DRY IRONING

For dry ironing, turn the variable steam control dial all the way to the right to “0”. This will cut off the steam flow if water is in the water tank. All marked fabric settings on the LED Display Panel can be used for dry ironing.

1.Plug the cord into a polarized, 120V AC electrical outlet. The power “ON” light will come on, indicating that the iron is receiving power.

2.Press on the electronic temperature control button to select the desired fabric/temperature setting. Turn the variable steam control dial to “0”. (See “Ironing Guide” for a guide to temperature selection.)

3.Place iron on its heel (on a stable, protected surface) while iron is warming to desired temperature.

STEAM IRONING

CAUTION! DO NOT aim iron at face, towards yourself, or

anyone else while using or adjusting steam. Burns or serious injury may occur.

WARNING! Before filling the iron with water, be sure the iron

is not plugged into the electrical outlet. The iron may be filled with water while it is hot.

CAUTION! TO PREVENT THE RISK OF BURNS, use caution

when filling iron with water. Burns can occur from touching hot metal parts, hot water, or steam.

NOTE: Because of the soleplate design, ordinary tap water may be used with this iron. However, in very hard water areas, we recommend using distilled or demineralized water.

WARNING: Never fill the iron with fabric conditioner, starches

or any other liquid, as these will damage the steam mechanism. Do not use contaminated water.

1.Open the water filling inlet cover. Holding the iron at a slight angle, pour water slowly into the water filling inlet. See figure 1. Fill tank to desired level or to the “MAX” water level marking using the water filling flask. (When the iron is upright, the see-through water tank allows you to gauge the amount of water.) DO NOT overfill the tank. When finished filling the iron with water, close the water inlet cover before continuing.

Fig. 1

2.Plug the cord into a polarized, 120V AC electrical outlet.

3.Press on the electronic temperature control button to select the desired fabric and temperature setting. Turn the variable steam control dial to the desired steam setting. (See “Ironing Guide” for a guide to temperature selection.)

GI490XH specifications

The Euro-Pro GI490XH is a state-of-the-art vacuum cleaner designed to meet the diverse cleaning needs of modern households. With its innovative technology and user-centric features, this model stands out as an efficient, reliable solution for maintaining a clean living environment.

One of the standout features of the Euro-Pro GI490XH is its powerful suction capability. Equipped with a high-performance motor, it delivers strong suction that can tackle various types of debris, from fine dust to larger particles. This makes it suitable for different surfaces, including carpets, hardwood floors, and tiles. The adjustable suction settings allow users to tailor the performance based on the surface being cleaned, ensuring optimal results every time.

The design of the GI490XH focuses on user convenience and versatility. It features a lightweight construction, making it easy to maneuver around the home. The vacuum cleaner is also equipped with a long reach hose and a variety of attachments, allowing users to clean hard-to-reach areas such as corners, upholstery, and even car interiors. The inclusion of a crevice tool, dusting brush, and upholstery nozzle enhances its versatility, enabling efficient cleaning of various surfaces and materials.

Another key characteristic of the Euro-Pro GI490XH is its advanced filtration system. The vacuum is designed with a HEPA filter, which captures allergens and microscopic particles, providing cleaner air as a result of the cleaning process. This makes it an excellent choice for allergy sufferers and families with pets. The filter is washable and reusable, adding to the eco-friendliness of the product while reducing the costs of maintenance.

In terms of technology, the Euro-Pro GI490XH features innovative smart sensors that help optimize cleaning patterns. These sensors detect dirt levels and adjust the suction power accordingly, ensuring that energy is used efficiently without compromising cleaning performance. The vacuum also includes an easy-to-empty dust container, minimizing the hassle of maintenance and allowing for quick disposal of collected debris.

Overall, the Euro-Pro GI490XH is a high-performance vacuum cleaner that combines powerful suction, user-friendly design, and advanced filtration technology. With its versatile attachments and smart cleaning capabilities, it is an ideal solution for those seeking an efficient and effective way to maintain cleanliness in their homes. The blend of innovation and practicality makes this vacuum a valuable addition to any cleaning arsenal.