Sunbeam 6062 If you leave the iron, To reset the iron, To use the Storage Strip Indicator

Page 5

MOTION SMART® AUTO-OFF FEATURE

When the iron is plugged in, the Off Indicator will blink, indicating there is power to the iron.

If you leave the iron:

In a horizontal position without moving it, or acciden- tally tip the iron over, it will automatically stop heating after 30 seconds. The Off Indicator will blink to let you know that the iron has stopped heating.

In a vertical position (on its heel rest) without moving it, the iron will automatically turn off after 15 minutes. The Off Indicator will blink to let you know that

the iron has stopped heating.

To reset the iron:

Move the iron back and forth. The Off Light will stop blinking and the iron will start heating again.

IMPORTANT: The Off Indicator will continue to blink for 5 minutes after the auto-off has activated. The iron will then turn off completely and no lights will be displayed. To re-activate the iron press the ▲ or ▼ Fabric Select buttons.

WARNING: The Motion Smart® Auto-Off is a safety fea- ture, not a recommended means for turning your iron off. See “Caring for Your Iron After Use” for information

on turning off your iron and storing it safely between use.

STORAGE STRIPINDICATOR

The Storage Strip™ indicator is an easy way to see when the iron is cool enough to store.

To use the Storage Strip™ Indicator:

Turn iron on. In approximately 3 minutes, the Storage Strip™ indicator will turn from black to red, indicating that the iron is too hot to store. When the iron is turned off, it will take the iron approximately 55-65 minutes for the Storage Strip™ indicator to turn from red to black, in- dicating that the iron is cool enough to store.

CAUTION: The Storage Strip™ indicator should only be used as a guideline. The iron should always be handled and stored with care.

CORD LOCKFEATURE

Cord Lock™ Feature locks in the left of right position to keep the cord out of your way and off your clothes.

ANTI-CALCIUM SYSTEM

The Anti-Calcium System is a permanent system located inside the water reservoir. This system removes calcium from the water and reduces calcium build-up on the sole- plate.

DRIP-FREE

Produces steam without any dripping, spitting, or leaking through the soleplate, even at low temperatures.

EMPTY WATER MODE

When the water in the reservoir is low, the water-level sen- sor will emit two short beeps then one longer beep. The iron will automatically switch to Steam OFF mode, and the Steam LED light will turn off.

1.To refill and reset the sensor, fill the water reservoir with water, then press either the Turbo Steam™, Shot of Steam® or Steam ON button to allow the sensor to find the new water level and reset. Steam ironing can then be resumed.

2.If steam ironing is attempted, but the water reservoir is NOT refilled, the sensor will detect this and emit two short beeps followed by one longer beep, and the iron will switch again to Steam OFF mode until refilled.

NOTE: If you do not refill and reset the sensor you may experience excessive noise and vibration.

CARING FOR YOUR IRON AFTER USE

TURNING OFF YOUR IRON

1.Use Fabric Select buttons (▲ ▼) to scroll to Off position and unplug iron.

WARNING: NEVER yank the power cord when unplugging the iron. This can damage the cord.

Storing Your Iron

1.Allow the iron to cool.

2.If you do not use your iron on a daily basis, empty the water reservoir after each use for a longer iron life. To do so, unplug the iron, turn the iron upside down, open the fill hole cover, and allow water to flow from the fill hole. Shake the iron gen- tly to remove trapped water drops.

3.Loosely loop the power cord around the heel rest and store the iron on its heel rest.

IMPORTANT: Wrapping the cord around the iron too tightly can damage the cord.

MAINTAINING YOUR TURBO STEAMIRON

CLEANING THE SOLEPLATE

Clean the soleplate if starch or other residue accumulates.

To clean the Soleplate:

1.Unplug the iron. Allow the iron to cool and then wipe it with a soft, damp cloth.

WARNING: DO NOT use abrasive cleansers, scouring pads or vinegar to clean the soleplate. This will damage the finish.

2. Run the iron over an all-cotton cloth to remove any residue.

USING THE SELF-CLEAN FEATURE

You should use the Self-Clean feature once a month to maintain the optimal performance of your iron.

To use the Self-Clean feature:

1.Fill the water reservoir with tap water to the MAX line.

2.Plug in the iron and press Fabric Select button to Linen. Allow the iron to heat until the Wait/Ready Light turns GREEN.

3.Unplug the iron.

4.Hold the iron over a sink in a horizontal position. WARNING: Be careful not to touch the iron’s hot surfaces.

5.Press the Self-Clean button and hold. Water will begin dripping from the steam vents. Slowly rock the iron side to side and front to back for 30 seconds. When rocking the iron, dip the nose of the iron slightly below the rear of the iron to make certain the water circulates completely.

6.Turn the iron upside down and allow the remaining water to flow out of the fill hole.

7.Dry the soleplate with a towel.

8.Plug in the iron and press Fabric Select button to Linen. Let the iron heat until the button turns GREEN and dry out the iron completely.

9.Press the Fabric Select button to Off. The light will go out, indicating that the iron has turned itself off. Unplug the iron and allow it to cool.

CLEANING THE ANTI-CALCIUM SYSTEM

The Turbo Steam™ iron houses an Anti-Calcium filter in the reservoir, which eliminates impurities from the water.

To prolong the efficiency of this filter:

1.Unplug the iron and allow it to cool.

2.Locate the water cup that accompanied the iron and fill it with water. Add 1 teaspoon of salt to the water and fill the water reservoir with this solution.

3.Leave the solution inthe waterreservoirfor 15 minutes,thenempty it.

4.Fill the water reservoir a second time with the salt water solution and empty it again after 15 minutes.

5.Fill the tank with fresh water to rinse and empty.

The Anti-Calcium System should be cleaned approximately once a month.

Image 5
Contents Modelo Important Safeguards Ironing Guide To Fill the Water Reservoir Selecting Fabric SettingsDRY Ironing Steam IroningTo use the Storage Strip Indicator To reset the ironTo clean the Soleplate To use the Self-Clean featureIroning Tips Year Limited Warranty Precauciones Importantes Guía DE Planchado Selección DE Telas Funciones SU Plancha Turbo SteamPlanchado EN Seco Planchado CON VaporMantenimiento DE SU Planchaturbo Steam Cuidado DE SU Plancha Después DE UsarlaPara prolongar la eficiencia de este filtro Recomendaciones Para EL PlanchadoGarantía Limitada de 1 Año For product questions Jarden Consumer Service USA Canada