Baracoda L (1D) manual Barcode Prefix/Suffix, Set Data prefix Set Data suffix End of configuration

Page 21

Data Capture for Workforce in Motion

Set Data prefix

Set Data suffix

End of configuration

1.8.3.Barcode Prefix/Suffix

You can add a barcode prefix and/or suffix (strings of more than 32 characters will not be accepted) to every barcode sent to the host device.

There is no barcode prefix or suffix in default settings.

Enable barcode prefix

Disable barcode prefix (*)

Enable barcode suffix

Disable barcode suffix (*)

If enabled, a Barcode prefix/suffix can be set in the same manner as the Data prefix/suffix can be set:

Set Barcode prefix

Set Barcode suffix

End of configuration

RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.5

- 21 -

Image 21

Contents RoadRunners Evolution -L 1D & -LA Laser Programming Guide Summary Appendix 1 Ascii Table A-Z, A-Z, 0-9, PUNCTUATION, Control Document Date Description Revision HistoryIntroduction Reset to factory settings General default settingsSwitch on delay Baracoda advanced featuresShutdown timers Turn scanner OFFNo data loss mode and Baracoda Header Reading ModeAiming Trigger Mode Trigger« no duplicate scans » enabled + no decoding AutoscanSmart Autoscan Real Time mode Operating ModeReal Time mode with No Data Loss option Batch modeNo Data Loss mode Enable ACK beep Real Time modeNo Data Loss mode Disable ACK beep Real Time Buffered data optionBatch Mode Batch modeDifferent connection methods Master modeLED on Buzzer and Led SettingsBluetooth name Bluetooth settingsSniff period settings Security code PIN settings RF Power emission settingsDisable BT security code Enable BT security code Data format Timestamp option Timestamp on Timestamp off YES End Procedure to define Data/Barcode Prefix/Suffix Data Prefix/SuffixStart Set Data prefix Set Data suffix End of configuration Set Barcode prefix Set Barcode suffix End of configurationBarcode Prefix/Suffix AIM Symbology Identifier Enable/Disable All Symbologies Decoder default settingsSet Decoder Default Settings Disable all symbologies Enable all symbologiesSet barcode length END of config VotingVoting = Start set min length Start Set Max length End of config Min/Max length per symbologySymbology table Codabar settingsEnable/Disable Codabar Disable EnableCodabar Check Digit Verification AIM recommendation Codabar Start/Stop charactersSet Lengths for Codabar Not transmitted TransmittedEnable/Disable Code Code 11 SettingsCode 11 check digits verification Transmit Code 11 check digitsEnable/Disable Code 39 Full Ascii Code 39 settingsEnable Disable Code 39 Start/stop charactersAccepted Code 39 characters Code 39 Check Digit VerificationSet lengths for Code Code 93 Settings Italian PharmaCode settingsCode 93 not active Code 93 active Code 128 Settings Enable/Disable Code 128/EANSet lengths for Code 128/EAN Define GS replacement character End of configuration Enable GS transmission Disable GS TransmissionEAN 128 Group Separator Define as GSEnable/Disable AIM ID Transmission Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Interleaved 2of 5 Check DigitEnable/Disable MSI MSI Code SettingsSet lengths for Interleaved 2 MSI Check DigitEnable/Disable Standard 2 Standard 2 of 5 SettingsSet lengths for MSI Standard 2 of 5 Check DigitUPC/ EAN Settings Enable/Disable UPC/EANSet lengths for Standard 2 Transmit UPC-E Check Digit Transmit EAN13 Check DigitTransmit EAN 8 Check Digit Transmit UPC-A Check DigitUPC-A, UPC-E, EAN conversions Transmit UPC number system for UPC-EAdd-on digiits settings ISSN/ISBN settingsEnable/Disable GS1 DataBar 15. GS1 DataBar RSS 14 Settings15.2. GS1 DataBar 14 Check Digit Transmission 15.3. GS1 DataBar 14 Linkage flag TransmissionEnable/Disable GS1 DataBar Limited 16. GS1 DataBar RSS Limited Settings16.2. GS1 DataBar Limited Check Digit Transmission 16.3. GS1 DataBar Limited Linkage flag TransmissionCapital letters A-Z Small letters a-z Ponctuation Decimal numbers Control Characters Appendix 2 AIM symbology identifiers structure

Related manuals

Manual 49 pages 27.3 Kb