John Lewis JLTDC 05 Procedure, Adjusting the level of conductivity, Memorising the new setting

Page 17

Adjusting the level of conductivity

Water contains, a variable quantity of limestone and mineral salts of which quantities vary according to geographical locations thus varying its conductivity values.

Relevant variations of the conductivity of the water compared to those prefixed by the factory could slightly influence the residual humidity of the laundry at the end of the cycle.

Your dryer allows you to regulate the sensitivity of the drying sensor based on conductivity values of the water by using the following procedure.

To establish the hardness of your water to correspond with the table opposite please contact your local water authority.

Display

Conductivity

Approximative

degree

value (µS/cm)

 

 

 

 

 

 

 

 

C 0

 

 

Low

< 300

 

 

 

 

 

C 0

 

 

Medium

300 - 600

 

 

 

 

 

 

 

C 0

 

 

High

> 600

 

 

 

 

 

 

 

 

highest level; however, certain models may be configured differently.

Procedure:

Turn the programme selector dial to switch on the appliance

In selection mode press simultaneously the buttons 3 and 6 until «C0» appears on the digits.

Cooling 10 minutes

Off

Extra dry

Cottons

 

 

 

 

 

 

 

Dry cleaning

 

Store dry

 

 

 

 

Dry time

 

Drying

 

 

 

 

 

 

 

 

30 minutes

 

Cupboard dry

 

 

 

 

 

1.25

 

Cooling

60 minutes

 

Damp dry

 

 

 

 

 

 

End

90 minutes

 

Iron dry

 

 

 

 

 

 

 

 

Delicates

 

Machine iron dry

 

Door

Alarm

Quick

Half

Delay

Start/

Filter

 

 

off

power

start

Pause

Full tank

 

 

Extra dry

 

1

2

3

4

5

6

 

 

Synthetics

Condenser

 

 

Cupboard dry

 

 

 

 

 

 

 

 

 

JLTDCO5

 

 

 

 

 

 

 

 

 

 

 

Iron dry

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjusting the level of conductivity:

Press the button 5 sequentially: the level of conductivity is indicated by the lighting of the horizontal hyphens.

 

 

 

 

Dry time

 

Drying

 

 

 

 

 

 

 

 

 

 

 

 

Cooling

 

 

 

 

 

 

End

Door

Alarm

Quick

Half

Delay

Start/

Filter

off

power

start

Pause

Full tank

1

2

3

4

5

6

Condenser

JLTDCO5

 

 

 

 

 

 

Normally, the appliance is factory-set to the

Memorising the new setting:

Simultaneously press down the buttons 3 and 6 until the previous drying cycle time appears again on the display and the buzzer sounds.

17

Image 17
Contents SyntheticsCottons Use InstallationChild Safety Contents Environmental Information Your New Tumble DryerEnergy saving tips Description of the Appliance Technical Specifications Installation InstructionsUnpacking Stacking kit optional accessoryPositioning Door reversalPermanent connection Electrical connectionControl Panel Display Alarm codeEnd of programme Incorrect option selectionStart/Pause button Indicator LightsType of laundry Degree of drying Max-load Required Programme ChartType of laundry Drying time Max-load Programme Cooling 10 minutesOperating Sequence Care Labels you may find on your laundry Hints & Tips on DryingDo not overload the appliance Do not use the tumble dryer to dry the followingExternal cleaning Maintenance and CleaningCleaning the door Cleaning the filtersReservoir must be re-inserted correctly Cleaning the drumEmptying the water reservoir Adjusting the level of conductivity ProcedureMemorising the new setting Normally, the appliance is factory-set toTumble dryer does not start Something Not WorkingDrying takes too long or laundry is not Dry enoughPage John Lewis Partnership Victoria Street London SW1E 5NN