Frigidaire Coin- Operated Commercial Tumble Action Washer Unpacking, Installation

Page 6

UNPACKING

1.Cut the shipping carton along the dotted line along the base of the unit.

2.While in the carton carefully lay the washer on its back side.

3.Removethe styrofoam base.

4.Carefully return the washer to an upright position and remove the carton.

5.Carefully move the washer to within 4 feet (122cm) of the final location.

6.Remove the following from the back side of the washer:

3 bolts,

3 yellow plastic spacers,

2 or 3 metal "P" clamps.

BOLT

SPACER

"P" CLAMP

7.Remove the service panel from the front of the washer.

8.Remove the 4 nuts and 6 large washers that attach the 2 yellow shipping braces to the drum and the base. Lift up on the drum and remove the braces (a yellow ribbon surrounds the items to be removed). These braces must be removed to allow the power supply cord to be released from the shipping ring.

9.Remove the large styrofoam block located under the drum. Lift up on the drum, tilt the base of the foam block inwards toward the rear of the washer until free, then pull it out.

10.Remove and discard the yellow ribbon and label from the front of the washer.

11.From the rear of the washer, carefully pull out the power supply cord through the hole in the backsheet.

12.Replace the service panel and screws.

NOTE: If the washer is to be transported at a later date, the shipping support hardware must be reinstalled to prevent shipping damage.

INSTALLATION

1.Run some water from the hot and cold faucets to flush the water lines and remove particles that might clog up the water valve screens.

2.Remove the inlet hoses and rubber washers from the plastic bag and install the rubber washers in each end of the inlet hoses.

3.Carefully connect the inlet hose marked "HOT" to the outside "H" outlet of the water valve. Tighten by hand, then tighten another 2/3 turn with pliers. Carefully connect the other inlet hose to the inside "C" outlet of the water valve. Tighten by hand, then tighten another 2/3 turn with pliers. Do not

 

crossthread or over-tighten these connections.

4.

Connect the inlet hose ends to the HOT and

 

COLD water faucets tightly by hand, then

 

tighten another 2/3 turn with pliers. Turn the

 

water on and check for leaks.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Coin- Operated Commercial Tumble Action Washer Table of Contents Prevent Fire Protect ChildrenPrevent Injury Grounding Requirements PRE-INSTALLATION Requirements Drain RequirementsElectrical Requirements Location of Your WasherROUGH-IN Dimensions Under Inlets Counter BackInstallation UnpackingCrossthread or over-tighten these connections Tools Needed Coin BOX AdjustmentKeep a record of all coin-box key numbers StepRemove coin slide from coin chute Remove coin receiver block from coin slide see FigureChange coin sizing block Replace coin receiver block into slideParts List for series 7682 Quick-Change Start Mechanism Replacement PartsV8 Coin Chute Parts List Commercial Appliance Waranty Information

Coin- Operated Commercial Tumble Action Washer specifications

The Frigidaire Coin-Operated Commercial Tumble Action Washer is a reliable and efficient solution designed to meet the demands of laundromats, apartment buildings, and other commercial laundry facilities. This machine stands out due to its robust construction, user-friendly features, and energy-efficient technologies, making it a preferred choice in the competitive commercial washing market.

One of the primary features of the Frigidaire Coin-Operated Washer is its durable design. Built to withstand the rigors of daily use, the machine uses high-quality components that enhance its longevity. The heavy-duty cabinet is resistant to dents and scratches, ensuring it maintains its aesthetic appeal even after extensive usage.

Equipped with a generous wash capacity, this tumbler can handle large loads, making it ideal for high-traffic environments. It provides ample space for laundered items, reducing the number of cycles required and increasing overall efficiency. This capacity is paired with an efficient tumble action wash system that ensures thorough cleaning while being gentle on fabrics.

The washer also features a user-friendly interface, which allows customers to select desired wash settings easily. With multiple cycle options, including various water temperatures and wash times, users can customize their laundry experience to meet specific needs. The coin-operated mechanism is designed to accept various denominations, making transactions seamless and convenient for users.

Energy efficiency is a cornerstone of the Frigidaire design philosophy. The tumble action washer utilizes advanced technologies that help minimize water and energy consumption. Its high-efficiency motor optimizes performance while reducing operating costs, which is essential for business owners looking to maximize profitability.

Additional characteristics of the Frigidaire Coin-Operated Washer include a low vibration design, ensuring quieter operation than some traditional washers. Maintenance is straightforward, thanks to easy-access components, allowing service technicians to perform routine checks and repairs with minimal disruption.

In conclusion, the Frigidaire Coin-Operated Commercial Tumble Action Washer combines durability, efficiency, and user-friendly features, making it an exceptional choice for any commercial laundry setting. With its capacity, energy-saving technologies, and robust design, it promises to meet the needs of business owners and customers alike, solidifying its place as a leader in the commercial laundry machinery market.
Top Page Image Contents