Samsung H1245A H1290A manual Drain hose connection procedures, Positioning the drain hose

Page 9

Installing the Washing Machine

Connecting the water supply hose

1. Remove the adaptor from the

 

 

4. Connect the water supply hose to the

water supply hose.

 

 

adaptor. Pull down part (c) of the

 

 

c

water supply hose. When you release

 

 

part (c) the hose automatically connects

 

 

 

 

 

 

to the adaptor making a ’click’ sound.

2. First, using a “+” type screw driver,

 

 

5. Connect the other end of the water

loosen the four screws on the adaptor.

 

 

supply hose to the inlet water valve at

Next, take the adaptor and turn part(b)

 

 

the top of the washer. Screw the hose

following the arrow until there is a 5mm

 

 

clockwise all the way in.

gap.

 

 

 

3. Connect adaptor to the water tap by

 

 

• If the water tap has a screw type faucet,

tightening the screws firmly.

 

 

connect the water supply hose to the

Then, turn part (b) following the arrow

a

 

tap as shown.

and put(a) and (b) together.

b

 

 

 

 

 

NOTICE After completing connection, if water leaks from the hose, then repeat the same steps. Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor.

Note: The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be used.

Drain hose connection procedures

1.Holding down the handle of the

drain hose connector, put in the drain hose in desired direction.

: Fix the hose into the drainage hole, and give the hose connector a push to the body to fix the hose.

Positioning the drain hose

The end of the drain hose may be positioned in three ways:

Over the edge of a wash basin.

The drain hose must be placed at a height of between 60 and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the faucet with a piece of string to prevent the drain hose from moving.

ln a sink drain pipe branch

The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60 cm above the ground.

ln a drain pipe

Samsung recommends that you use a 65 cm high vertical pipe; it must be no shorter than 60 cm and no longer than 90 cm.

SAMSUNG Washing Machine Owner’s Instructions 5

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Washing Machine Owner’s Instructions Page Silver Wash Silver Nano Health System TM FeaturesSafety Precautions Before using the applianceSafety instructions Table of Contents Installing the Washing Machine Unpacking the Washing MachineOverview of the washing machine Adjusting the leveling feet Selecting a locationRemoving the shipping bolts To connect the water supply hose Connecting the water supply hosePositioning the drain hose Drain hose connection proceduresPlugging in the machine Wiring lnstructionsWashing a Load of Laundry Washing for the first timePutting detergent in the washing machine Overview of the control panel Temperature selection buttonChildlockbutton lock function For the Silver Wash washingMemory selection button Washing clothes using Fuzzy LogicWashing clothes manually Using Delay StartWashing tips and hints Using Clean TubCleaning the exterior Repairing a frozen washing machineMaintaining the Washing Machine Draining the washing machine in an emergencyCleaning the debris filter Cleaning the detergent drawer and recessTo do this Cleaning the water hose mesh filterTroubleshooting Problems and solutionsUnderstanding error messages User option Programme ChartFabric care chart AppendixElectrical warnings Specification Protecting the environmentDeclaration of conformity Contact Samsung World Wide
Top Page Image Contents