Indesit WD 12 S manual Simple with the new Indesit technology, you need less than

Troubleshooting

Before calling, read the following

In most cases, when your washer-dryer fails to work, the problems arising can be easily solved without having to call for a technician. Before calling for assistance, always check these points.

The washer-dryer fails to		the door is open or not shut			But where did all the water go?
					Simple: with the new Indesit technology, you need less than
start.
		properly.
					half of it, to get good results on twice as much!
	Is the plug correctly inserted	Is the	On/Off	button	This is why you cannot see the water through the door:
					because there is little, very little of it, to respect the
	into the socket? It could have	pressed?
					environment yet without renouncing maximum cleanliness.
	been moved whilst cleaning.	If it is, then a programmed start			And, on top of that, you are also saving electricity.
	Is there electricity in the	has been set.
	house?	Is the programmed start
	A circuit breaker may have	knob, in the correct position
	switched off as a result of too
		for	those	models
	many electrical appliances
		concerned?
	working at the same time. Or
		Is the water supply turned
	maybe due to a general failure
	in your entire area.	on? For safety reasons, if the
	Is the washer-dryer door	washer-dryer does not load
		water, it cannot start a wash
	closed properly?
		cycle.
	For safety reasons, the
	washer-dryer cannot work if					off, select one of the symbols
						stop/reset , then switch it

back on. If the knob continues to turn, call for assistance because it is showing an anomaly.

RIGHT	WRONG
Turn off the water	Leave the washer-dryer
supply after use.	plugged in while
This will eliminate	cleaning.
the possibility of	Even during maintenance,
leakage.	the appliance should
Always leave the	always be unplugged.
	Use solvents and
appliance door ajar
to avoid bad odours.	aggressive abrasives.
	Never use solvents or
Clean the	abrasives to clean the
appliance’s	external and rubber parts
exteriors gently.	of the washer-dryer.
To clean the	Neglect the detergent
exteriors and the
rubber parts of the	dispenser.
appliance, always	It is removable and can
use a soft cloth	easily be cleaned by
dipped in warm and	leaving it under running
soapy water.	water.
	Go on holiday without
	thinking about her.
	Before leaving, always
	make sure that the
	washer-dryer is
	unplugged and that the
	water supply is turned off.

The washer-dryer fails to fill with water.

Is the hose correctly connected to the tap?

Is there a water shortage ?

There could be work in progress in your building or street.

Is there sufficient water pressure? The autoclave may be malfunctioning.

Is the tap filter clean? If the water is very calcareous, or if work has recently been carried out on the water piping, the tap filter could be clogged with particles and debris.

Is the rubber hose kinked? The tract of the rubber hose bringing water to washer- dryer must be as straight as possible. Make sure it is not squashed or kinked.

The programme selector knob keeps turning?

Wait a few minutes for the drain pump to empty the tub, switch the washer-dryer

The washer-dryer continuously fills and drains water.

Is the drain hose positioned too low? It must be installed at a height ranging from 60 to 100 cm.

Is the end of the hose immersed in water?

Does the wall drainage system have a breather pipe? If the problem persists even after these checks, turn the water supply off the machine and call for assistance.

If you live on an upper floor of your building, there may be a problem with your drain trap.

To solve this problem, a special valve must be installed.

9Instructions for installation and use