Indesit pwdc instruction manual Indicator lights, Starting a wash cycle

Page 7

Indicator lights

The indicator lights provide important information. This is what they can tell you:

Delayed start

If the DELAY TIMER function has been activated (see “Per- sonalisation”), after the wash cycle has been started the indicator light corresponding to the selected delay period will begin to flash:

As time passes, the remaining delay will be displayed and the corresponding indicator light will flash:

The set programme will start once the selected time delay has expired.

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has be- gun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress.

Wash

GB

 

Rinse

 

Spin/Drain

 

Drying

 

End of wash cycle

END

Function buttons and corresponding indicator lights When a function is selected, the corresponding indicator light will illuminate.

If the selected function is not compatible with the program- med wash cycle, the corresponding indicator light will flash and the function will not be activated.

If the selected function is not compatible with another function which has been selected previously, the indicator light corresponding to the first function selected will

flash and only the second function will be activated; the indicator light corresponding to the enabled option will remain lit.

Note: if the function is active, all other non-compatible functions cannot be activated.

Door locked indicator light

When the indicator light is on, the porthole door is locked to prevent it from being opened; make sure the indicator light is off before opening the door (wait approximately 3 minutes).

To open the door during a running wash cycle, press the START/PAUSE button; the door may be opened once the DOOR LOCKED indicator light turns off.

!If the “functions” and START/PAUSE indicator lights flash fast and the “current phase” and DOOR LOCKED indicator lights turn on, there is an anomaly (see “Troubleshooting”).

Starting a wash cycle

1.Turn the washer-dryer on by pressing the ON/OFF button. All the indicator lights will turn on for a few seconds, then only the indicator lights relative to the selected programme settings will remain lit and the START/PAUSE indicator light will flash.

2.Load the laundry and close the door.

3.Set the WASH CYCLE knob to the desired programme.

4.Set the washing temperature (see “Personalisation”).

5.Set the drying cycle if necessary (see “Personalisation”).

6.Measure out the detergent and washing additives (see “Detergents and laundry”).

7.Select the desired functions.

8.Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed man- ner, in blue. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9.At the end of the wash cycle the indicator light will switch on. The door can be opened once the DOOR LOCK indi- cator light turns off (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch the washer-dryer off by pressing the ON/OFF button.

7

Image 7
Contents WASHER-DRYER Instructions for useConnecting the electricity and water supplies InstallationUnpacking and levelling If a replacement fuse cover is fitted, it must be Before using the appliance please read the instructionsBe used until a replacement is obtained Replacement fuse coversDisposing of the appliance First wash cycleTechnical data Control panel ON/OFF button switches the washer-dryer on and offDescription of the washer-dryer Starting a wash cycleStarting a wash cycle Indicator lightsWash Rinse Spin/Drain Drying End of wash cycle Table of wash cycles Wash cyclesFunctions Setting the temperatureSetting the drying cycle PersonalisationLoad balancing system Detergents and laundryDetergent dispenser drawer Preparing the laundryDisposing of the packaging materials Precautions and tipsGeneral safety DisposalCutting off the water and electricity GB supplies Care and maintenanceCleaning the washer-dryer Cleaning the pumpProblem Possible causes / Solutions TroubleshootingFeet have not been adjusted, enabling the machine to rock Opened Program has finished ProcedureGent and no laundry Machine door cannot beAssistance Replacement of any removable parts made of glass or plasticRecycling & Disposal Information After Sales Service195088128.02 Essential Contact Information