Hotpoint WDF 760 P/G/A/K Installation, Unpacking and levelling, Electric and water connections

Page 2

Installation

! Keep this instruction manual in a safe place for

GB

future reference. Should the appliance be sold,

 

 

transferred or moved, make sure the instruction

 

manual accompanies the Washer-dryer to inform

 

the new owner as to its operation and features.

 

! Read these instructions carefully: they contain

 

vital information on installation, use and safety.

 

Unpacking and levelling

 

Unpacking

 

1. Unpack the Washer-dryer.

 

2. Check whether the Washer-dryer has been

 

damaged during transport. If this is the case, do

 

not install it and contact your retailer.

3. Remove the 2

protective screws and the rubber bush with

the respective spacer,

situated on the rear of the appliance (see also the installation leaflet). NB:The plastic spacers may fall down inside the machine once the bolt

has been removed, and will not interfere with the operation of the machine.

4.Do not remove external bar.

5.Seal the gaps using the plastic plugs provided.

6.Keep all the parts: you will need them again if the Washer-dryer needs to be moved to another location.

!Packaging materials are not children's toys.

Levelling

Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly.

1.Install the Washer-dryer on a flat sturdy floor, without resting it up against walls, furniture cabinets or other.

2.If the floor is not perfectly level, com- pensate for any

unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured according to the worktop, must not exceed 2°.

Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the Washer- dryer.

Electric and water connections

Connecting the water inlet hose

1. Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with a 3/4 gas threaded mouth

 

 

A

(see figure).

 

 

 

 

 

 

Before making the

 

 

 

connection, allow the

 

 

 

water to run freely until

 

 

 

it is perfectly clear.

 

 

 

2. Connect the other end

 

 

 

 

 

 

of the water inlet hose to

 

 

 

the Washer-dryer,

 

 

 

screwing it onto the

 

 

 

appliance's cold water

 

 

 

inlet, situated on the top

 

 

 

right-hand side on the

 

 

 

rear of the appliance (see

 

 

 

figure).

 

 

 

 

3.Make sure there are no kinks or bends in the hose.

!The water pressure at the tap must be within the values indicated in the Technical details table (on the next page).

!If the water inlet hose is not long enough, contact a specialist store or an authorised serviceman.

!Ensure that the supply taps are allowing water through. Old taps may seize in the closed position and thus prevent water reaching the machine.

Image 2
Contents Instructions for use WASHER-DRYERElectric and water connections InstallationUnpacking and levelling Connecting the drain hose First wash cycle U E Neutral N O W N Live L Green & Yellow Earth ETechnical data Description of the Washer-dryer and starting a wash cycle Control panelIndicator lights Starting a wash cycleWash cycles Table of wash cyclesPersonalisation Setting the temperatureSetting the drying cycle FunctionsGarments requiring special care Detergents and laundryDetergent dispenser drawer Preparing the laundryDisposal Precautions and tipsGeneral safety Opening the porthole door manuallyCare and maintenance Possible causes / Solutions TroubleshootingProblem Guarantee AssistanceAfter Sales Service 195071353.00