JVC KD-G464 manual Typical connections, Connecting the external amplifier

Page 32

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the receiver.

•Be sure to ground this receiver to the car’s chassis again after installation.

Notes:

•Replace the fuse with one of the specifi ed rating. If the fuse blows frequently, consult your JVC car audio dealer.

•It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 20 of the INSTRUCTIONS).

•To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this receiver.

Heat sink

A Typical connections

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this receiver.

The leads of the power cord and those of the connector from the car body may be different in color.

1Connect the colored leads of the power cord in the order specifi ed in the illustration below.

2Connect the antenna cord.

3Finally connect the wiring harness to the receiver.

Rear ground terminal

Antenna terminal

To CD changer or another external component (see diagram )

15 A fuse

Line out (see diagram )

Black

Yellow*2

Red

*1 Not included for this receiver

Ignition switch

To metallic body or chassis of the car

 

To a live terminal in the fuse block connecting to the car battery

 

(bypassing the ignition switch) (constant 12 V)

 

To an accessory terminal in the fuse block

Fuse block

 

*2 Before checking the operation of this receiver

prior to installation, this lead must be connected,

Blue

otherwise power cannot be turned on.

To the automatic antenna if any (250 mA max.)

 

 

Blue with white stripe

 

To the remote lead of other equipment (200 mA max.)

White with black

White

Gray with black stripe

Gray

Green with black stripe

Green

Purple with black stripe

Purple

stripe

 

 

 

 

 

 

 

 

Left speaker (front)

Right speaker (front)

Left speaker (rear)

Right speaker (rear)

B Connecting the external amplifier

You can connect an amplifi er to upgrade your car stereo system.

•Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this receiver.

•Disconnect the speakers from this receiver, connect them to the amplifier. Leave the speaker leads of this receiver unused.

Rear speakers

Remote lead

Y-connector (not supplied for this receiver)

JVC Amplifier

Remote lead (Blue with white stripe)

Signal cord (not supplied for this receiver)

To the remote lead of other equipment or automatic antenna if any

*3 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place not coated with paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the receiver.

Front speakers

C Connecting other external components

CD changer

Signal cord supplied for your CD changer

JVC CD changer

External component

KS-U57*3

Signal cord (not supplied for this receiver)

CD changer jack

External component

CAUTION

•Before connecting the CD changer, make sure that the receiver is turned off.

*3 Line Input Adapter KS-U57 (not supplied for this receiver)

2

Page 31 Page 32
Image 32
Page 31 Page 32
Contents KD-G464 How to forcibly eject a disc How to reset your unitContents How to read this manual How to use the Mode buttonDisplay window Control panel KD-G464Parts identification Remote controller RM-RK50 Installing the lithium coin battery CR2025To drop the volume in a moment ATT To turn off the powerGetting started Basic operationsSetting the clock Canceling the displayTo activate the display demonstration DemonstrationsWhen an FM stereo broadcast is hard to receive Radio operationsListening to the radio To tune in to a station manuallyManual presetting SSM Strong-station Sequential MemoryDisc operations Playing a disc in the receiverAbout MP3 and WMA discs To stop play and eject the discPlaying discs in the CD changer About the CD changerTo fast-forward or reverse the track To go to the next or previous tracksSkipping a track quickly during play Other main functionsProhibiting disc ejection While playing an MP3 / or WMA disc Changing the display informationWhile playing an audio CD or a CD Text Mode Mode Plays repeatedlySelecting the playback modes Sound adjustments For Preset valuesAdjusting the sound To do RangeGeneral settings PSM Basic procedureIndications Selectable settings, reference Detaching the control panel Detaching the control panelExternal component operations Playing an external componentMaintenance More about this receiver General settings-PSM Playing an MP3/WMA discChanging the source Ejecting a discTroubleshooting Symptoms Causes RemediesMP3/WMA playback CD changer Specifications Audio Amplifier SectionRefer to page of How to reset your unit Having Trouble with operation?Installation/Connection Manual Parts list for installation and connectionPrecautions on power supply and speaker connections Removing the receiverTypical connections Connecting the external amplifierConnecting other external components

KD-G464 specifications

The JVC KD-G464 is a versatile and feature-rich car stereo that caters to the needs of music enthusiasts looking for a reliable audio companion on the road. With its sleek design and user-friendly interface, it showcases a perfect blend of aesthetics and functionality.

One of the standout features of the KD-G464 is its ability to support a wide range of media formats. This unit is equipped with a CD player that not only plays standard CDs but also supports CD-R and CD-RW formats, allowing users to enjoy their favorite music without constraints. Additionally, the front panel includes a convenient USB port, making it easy to connect flash drives and access digital music files directly. This feature is complemented by the compatibility with MP3 and WMA audio formats, ensuring that your collection is played with excellent sound quality.

The JVC KD-G464 is designed with advanced features that enhance the listening experience. Its built-in 4-channel amplifier delivers a robust output power of 50 watts per channel, ensuring that every note is crisp and clear. The EQ (Equalizer) preset settings further allow users to customize their audio output by adjusting the treble, midrange, and bass levels according to personal preferences.

Additionally, the unit features a detachable faceplate, providing an added layer of security against theft. This design is complemented by a high-contrast LCD display that makes it easy to read song information and control settings, even in bright daylight. The user interface is intuitive, allowing quick access to all functionalities without overwhelming the driver.

The KD-G464 also highlights its compatibility with various smartphone technologies. It is designed to work seamlessly with devices that support Bluetooth, enabling hands-free calling and audio streaming directly from mobile phones. This ensures that users can stay connected while keeping their focus on the road.

In terms of connectivity, the receiver includes auxiliary input, allowing users to connect external devices, such as MP3 players or other audio sources. With its robust feature set and advanced technologies, the JVC KD-G464 stands out as an excellent choice for anyone seeking an upgrade to their vehicle's audio system. Whether you’re commuting or hitting the open road, this unit promises to enhance your driving experience through quality sound and versatile connectivity options.
Top Page Image Contents