Frigidaire P/N 134296400A (0404) Electrical Connections For 3-WIRE System

Page 8

GREEN

 

GROUND

 

SCREW

SILVER TERMINAL

 

GREEN

NEUTRAL

GROUND

WIRE

NUT

TIGHTEN NUT

TO THESE

THREADS

STRAIN

 

RELIEF

 

MOUNTING

 

BRACKET

POWER CORD

 

ELECTRICAL CONNECTIONS

FOR 3-WIRE SYSTEM

Non-Canadian ELECTRIC Dryer

1.Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner.

2.Install a U.L. approved strain relief into the power cord entry hole of the mounting bracket. Finger tighten the nut only at this time.

3.Thread a U.L. approved 30 amp. power cord, NEMA 10-30 Type SRDT, through the strain relief.

4.Attach the power cord neutral (center wire) conductor to the silver colored center terminal on the terminal block. Tighten the screw securely.

5.Attach the remaining two power cord outer conductors to the outer brass colored terminals on the terminal block. Tighten both screws securely.

Do not make a sharp bend or crimp wiring/ conductor at connections.

6.Reattach the strain relief mounting bracket to the back of the dryer with two screws. Tighten screws securely.

7.Tighten the screws securing the cord restraint firmly against the power cord.

8.Tighten the strain relief nut securely so that the strain relief does not turn.

9.Reinstall the terminal block cover.

 

 

GREEN POWER

CORD

 

 

 

 

 

GREEN

 

 

 

 

 

GROUND WIRE

 

SILVER TERMINAL

 

 

 

 

 

 

 

GROUND

 

 

 

 

 

 

 

 

SCREW

 

 

 

TERMINAL BLOCK

 

 

 

 

 

 

 

GREEN

 

 

 

 

 

TIGHTEN

 

 

BLACK

NEUTRAL

 

 

 

 

 

 

 

NUT

GROUND

 

 

 

 

 

 

TO THESE

WIRE

WHITE

 

 

 

 

THREADS

 

 

 

 

 

 

 

 

 

NUT

RED

STRAIN

RELIEF

MOUNTING

BRACKET

POWER

CORD

ELECTRICAL CONNECTIONS

FOR 4-WIRE SYSTEM

Non-Canadian ELECTRIC Dryer

1.Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner.

2.Install a U.L. approved strain relief in the entry hole of the mounting bracket. Finger tighten the nut only at this time.

3.Remove the green neutral ground wire from the green ground screw located above the terminal block.

TYPICAL 4

CONDUCTORBLACK 240V

RECEPTACLE

 

 

WHITE NEUTRAL

 

 

RED 240V

TYPICAL 4

 

 

 

CONDUCTOR CORD

 

 

 

 

GRE

EN GROUND

 

 

 

 

 

 

30 AMP NEMA 14-30 TYPE SRDT OR ST

4.Thread a U.L. approved 30 amp power cord, NEMA 14-30 type ST or SRDT through the strain relief.

5.Attach the green power cord ground wire to the cabinet with the green ground screw.

6.Attach the white (neutral) power cord conductor from the power cord and the green ground wire from the dryer harness to the silver-colored center terminal on the terminal block. Tighten the screw securely.

7.Attach the red and black power cord conductors to the outer brass-colored terminals on the terminal block.

Do not make a sharp bend or crimp wiring/ conductor at the connections.

8.Tighten the screws securing the cord restraint firmly against the power cord.

9.Tighten the strain relief nut securely so the strain relief does not turn.

10.Reinstall the terminal block access cover.

8

Image 8
Contents Installation Instructions Exhaust System Requirements PRE-INSTALLATION RequirementsElectrical Requirements Exhaust Duct Locating Dimensions GAS Supply RequirementsVent Hood Type Exhaust DirectionDo not Install Your Dryer Installation in Recess or ClosetDo not Install Your Dryer in a Closet with a Solid Door Location of Your DryerMobile Home Installation Home USE onlyTOP Console Models UnpackingReversing Door Swing To change the direction of the door openingElectrical Installation Grounding RequirementsNon-Canadian Electric Dryer Canadian Electric DryerElectrical Connections For 3-WIRE System Electrical Connections For 4-WIRE SystemInstallation Replacement PartsOpen the shutoff valve in the gas supply line Resting Solid on ALL Four Legs