Creda TCS3 manual Installation, Before you start using your dryer

Page 4

GB

Installation

! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the dryer works.

!Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works.

Door Reversal Instructions

 

 

Hinge

 

Door catch

 

 

 

 

 

 

 

Door latch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hinge

The door of your dryer is reversible and can easily be changed. Exchange diagonally hinge brackets and blanking screws. Exchange door latch and catch with their opposite blanking plates (see diagram above).

Where to put your dryer

Place your dryer at a distance from gas ranges, stoves, heaters, or cook tops because flames can damage the appliance.

If you are going to install the appliance under a work counter, be sure to leave a 10mm space between the top and any other objects on or above the machine and a 15mm space between the sides and lateral furnishings or walls. This is to ensure proper air circulation. Make sure that the back vents are not obstructed.

Ventilation

When the dryer is in use, there has to be adequate ventilation. Make sure you put your dryer in an environment that is not damp and has proper air circulation throughout. Airflow around the dryer is essential to condense the water produced during the washing, the dryer will not operate efficiently in an enclosed space or cupboard.

!If using the dryer in a small or cold room some condensation could be experienced.

Water drain

If your dryer is installed next to a drain the water can be plumbed into this drain. This does away with the need to empty the water container. Simply remove the top hose from its top fitting at the rear of the dryer and plumb the hose provided to the drain.

Electrical connections

Make sure of the following before you insert the plug into the the electrical socket:

The socket must be grounded.

The socket must be able to sustain the machines maximum power, which is indicated on the rating label (see Dryer Description).

Power voltage must be within the values indicated on the rating label (see Dryer Description).

The socket must be compatible with the dryers plug.

Should this not be the case, replace the plug or the socket.

!The dryer must not be installed outdoors, even if the space is sheltered. It can be very dangerous if it is exposed to rain or storms.

!Once installed, the dryers electrical wire and plug must be within easy reach.

!Do not use extension cords.

!The power cord must not be bent or squashed.

!The power cord supplied is fitted with a BS1363 plug and a 13 amp BS1362 fuse. If you need to replace the fuse, use only those rated at 13 amp (13A) and ASTA approved to BS1362.

Moulded plug

!The plug must not be used without the fuse cover in place.

If a replacement fuse holder/cover is required, it must be of the same colour coding or wording as shown on the base of the plug.

Replacements are available from authorised dealers.

Changing the plug

The wires in the power cord are coloured in accordance with the following:

Green and Yellow (Earth) wire to terminal marked ‘E’, symbol , or coloured green and

yellow. 13A ASTA approved fuse to BS1362.

Blue (Neutral) wire to

 

 

terminal marked ‘N’ or

 

Brown (Live) wire to

coloured black.

 

terminal marked ‘L’ or

Cord clamp

 

coloured red.

 

 

 

 

!If the plug being replaced is a non-rewirable type, then the cut-off plug must be disposed of safely. DO NOT leave it where it can be inserted into a socket and create a shock hazard.

!The power supply cord should be checked periodically and replaced by a cord specially prepared for this dryer and fitted only by authorised technicians (see Service). New or longer power cords are supplied at an extra charge by authorised dealers.

!The manufacturer denies any responsibility should any of these rules not be followed.

!If in doubt about any of the above consult a qualified electrician.

Before you start using your dryer

Once you have installed your dryer and before you use it, clean the inside of the drum to remove any dust that could have accumulated during transport.

2

Image 4
Contents TCS3 Page Instruction booklet Tumble DryerInstallation Before you start using your dryerDryer Description To open the door FeaturesControl panel Choosing a programme Start and ProgrammesWater container and empty water light Programmes Speedy IronOptions available FabricSorting your laundry LaundryTypical load Special clothing items Drying timesDisposal General safetySaving energy and respecting the environment Maintenance and Care Problem Possible causes / Solution TroubleshootingTumble dryer won’t start Service Before calling the Service CentreWhat to tell the Service Centre Spare PartsPage Page Key Contacts