American Dryer Corp ML-145, ML-170 service manual To Replace Keyboard Touchpad Label Assembly

Page 21

8. Reestablish electrical power to the dryer.

To Replace Keyboard (Touchpad) Label Assembly

1. Discontinue electrical power to the dryer.

2. Unplug keyboard (touchpad) ribbon from rear of the microprocessor computer.

3. Slowly peel off and remove keyboard (touchpad) label assembly from control panel.

4. Peel paper backing off new keyboard (touchpad) label assembly.

5.Holding the new keyboard (touchpad) label assembly close to the panel, insert the keyboard (touchpad) ribbon through the rectangular slot in the control panel. Align label assembly into position by matching the red viewing window on the label to the rectangular cutout in the panel and gently press into place.

6.Connect keyboard (touchpad) ribbon to the computer.

7.Reestablish electrical power to the dryer.

To Replace Microprocessor Temperature Sensor Probe

1. Discontinue electrical power to the dryer.

2. Remove lint drawer. Remove two (2) screws securing lint door and remove lint door.

3. Remove microprocessor sensor bracket assembly from dryer.

a. Disconnect sensor bracket harness connector.

b. Loosen the two (2) Phillips head screws securing bracket assembly to dryer and remove bracket from dryer.

NOTE: DO NOT remove screws.

4.Disassemble sensor probe from bracket assembly by removing the top push-on fastener securing the probe from bracket. Use a small screwdriver to slowly pry the fastener off.

5.Disconnect the two (2) “orange” wires from the high heat (225º F [107º C]) thermostat, and remove modular bracket connector, wires, and probe from bracket assembly.

6.Install new sensor probe assembly (ADC Part No. 880251) by reversing procedure.

7.Reestablish electrical power to the dryer.

NOTE: If, when electrical power is reestablished, the microprocessor computer display reads “TEMP SENSOR FAIL,” check for a loose connection in the wiring.

17

Image 21

Contents American Dryer Corporation ML-145 / ML-170Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Section Technical Information Important Information Safety PrecautionsStandards Cleaning Routine MaintenanceLubrication AdjustmentsInstallation Requirements ENCLOSURE, AIR SUPPLY, and Exhaust RequirementsElectrical and GAS Requirements Operational Service Check Procedure Gas 10.5 inches water column 26.1 mb Control Panel Microprocessor Description of PartsControl Panel NON-MICROPROCESSOR Control BOXHSI HOT Surface Ignition Module GAS Burner AssemblyGas Models only Drive MotorIdler Assembly Blower Motor and Impellor GAS and SteamTumbler Basket Bearing and Pulley Arrangement Main Door Switch Sail Switch Gas Models onlyTumbler Basket Automatic Reset Thermostat HI-LIMIT Gas Models onlyLint Drawer Temperature Sensor Bracket NON-COMPUTER Lint Drawer SwitchSteam Damper System Compressed AIR RequirementsIntroduction ServicingComputer Controls To Replace ComputerTo Replace Microprocessor Temperature Sensor Probe To Replace Keyboard Touchpad Label AssemblyTo Remove Flame Probe Assembly Ignition ControlsTo Replace Gas Valve Refer to above burner illustration To Replace Main Burner Orifices To Test and Adjust Gas Water Column PressureTo Replace Burner Tubes To Convert from Natural Gas to L.P. GasTo Replace HSI Hot Surface Ignition Module ThermostatsTo Replace Burner Hi-Limit Thermostat Gas Models Only To Replace Sail Switch Sail Switch Assembly Gas Models onlyTo Replace Main Door Assembly To Adjust Sail SwitchTo Replace Front Panel To Install New Main Door GlassTo Replace Main Door Hinge Blocks PulleysTo Replace Tumbler Basket Pulley To Replace Large Idler Pulley To Replace Small Idler PulleyTumbler Basket Assembly Tumbler Basket Alignment Vertical Up and Down AdjustmentTo Replace Motor Pulley To Replace Tumbler Basket or Tumbler Basket Support Tumbler Basket Alignment Lateral Side to Side AdjustmentImportant Never strike the shaft directly with a hammer To Replace Front Idler Shaft Pillow Block Bearing To Replace Front Tumbler Basket Support Pillow Block BearingBelt Tension Adjustment Tumbler Basket to Idler To Replace Rear Idler Shaft Pillow Block BearingBelts Refer to illustrations in section F Pulleys To Replace V-Belts Belt Tension Adjustment Motor to IdlerMotors To Replace Drive MotorImpellor To Replace Lint Drawer Switch Lint Drawer Assembly To Replace Lint ScreenComputer will not accept keyboard touchpad entries TroubleshootingDisplay is reading no Airflow Display is reading Rotation Sensor FailDisplay is reading Drum Safety Fail Display is reading Sail Switch FailDisplay is reading Burner Safety Fail Display is reading No HeatDisplay is reading Burner Flame Failure Display is reading Burner Control FailureDisplay is reading Main Door Display is reading Lint DoorDisplay is reading Hot Dryer operates but is taking too long to dryThermal overload for drive motor is tripping There is excessive vibration coming from the tumbler basket Overload for impellor fan motor is trippingElectrical Troubleshooting Diagnostic L.E.D. light emitting diode Display Failure Codes Phase 6 OPL System DiagnosticsPage E.D. Display Indicator Number E.D. light emitting diode Display IndicatorsE.D. Display Indicator Number FAN Blower Output L.E.D. light emitting diode Indicator AIR AIR JET Output L.E.D. Indicator OptionalHT1 Heat Output L.E.D. Indicator Lint Lint Door Input L.E.D. Indicator Fuse Main Fuse Input L.E.D. IndicatorMain Main Door Input L.E.D. Indicator Drum Tumbler Basket HI-LIMIT Input L.E.D. IndicatorPower Supply Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. IndicatorE.D. Display Operating Status D. DISPLAY/CODESPhase 6 OPL Microprocessor L.E.D. Displays ALL REV E.D. Codes 1. Display CodesGAS Models only Power 24 VAC is not Evident AT GAS Valve GAS/ELECTRIC only BURNER/OVEN Open HI-LIMIT CircuitGAS only Ignition Attempt Failure Computer Logic and Wiring Diagram No Display Condition Blower motor does not operate, drive motor runs No Heat Drive and Blower Motors Run Steam Models No Heat Drive and Blower Motors Run Gas ModelsDoor Condition Motor Plate High and LOW Voltage Technical InformationInformation on the Data Label Data LabelHow to Use a Manometer Using a ManometerML-170 Tool List ADC 450429 1- 02/18/00-25