American Dryer Corp AD-30, AD-25 service manual Tumbler Alignment Lateral

Page 38

TUMBLER ALIGNMENT (LATERAL)

1.Discontinue power to the dryer.

2.Remove the back guard.

3.Loosen the two (2) hex head bolts, (one [1] turn is enough), that holds the pillow block bearing to the bearing box.

4.Back off the two (2) jam nuts on the side adjustment bolts. Now, rotate the tumbler from the front of the dryer, checking the space between the tumbler and the front panel. This should be equal on the left hand and right hand side.

5.Lateral adjustment (viewing from the rear).

a.Loosening (by turning counterclockwise) the left hand adjustment bolt and tightening (by turning clockwise) the right hand adjustment bolt will shift the tumbler to the right.

b.Loosening (by turning counterclockwise) the right hand adjustment bolt and tightening (by turning clockwise) the left hand adjustment bolt will shift the tumbler to the left.

6.Tighten and secure both adjustment bolts and jam nuts.

7.Tighten the bearing box bolts.

8.Replace the back guard and reestablish power to the dryer.

38

American Dryer Corp.

450268-1

Page 37 Page 39
Image 38
Page 37 Page 39
Contents AD-25, 30, 50, 75 Phase 7.2 Non-Coin Retain This Manual in a Safe Place for Future Reference Table of Contents Safety Precautions Explosion could ResultRoutine Maintenance CleaningAdjustments LubricationInstallation Requirements ENCLOSURE, AIR SUPPLY, and Exhaust RequirementsElectrical and GAS Requirements Operational Service Check Procedure Control BOX Computer Controls Main Door SwitchControl Panel Microprocessor Tumbler Lint Drawer SwitchLint Drawer Drive Motor and Blower Motor Tumbler Bearing and Pulley ArrangementIdler Bearing Steam Damper System Temperature Sensor Computer ControlsGAS Burner Electric Oven Sail Switch Electric and GAS ModelsCompressed AIR Requirements Reversing Relay Panel Motor Contactor 1Ø MOT orNON-REVERSING Contactor 3Ø MOT or HI-LIMIT Thermostat GAS and Electric Models only To Replace Control Panel Assembly Controls ComputerTo Replace Computer To Replace Keypad Refer to illustration aboveTo Replace Computer Temperature Sensor Probe To Replace Motor Contactor 3-POLE, 24 VACBurner Controls GAS To Replace Spark IgnitorTo Replace Main Burner Orifices To Test and Adjust GAS Water Column W.C. PressureTo Replace GAS Valve American Dryer Corp 450268-1 To Convert from Natural to Liquid Propane L.P. GAS Are Made of BRASS, Which is Easily DamagedTo Replace Burner Tubes To Replace Direct Spark Ignition DSI ModuleInstallation Steam ControlsTo Replace Steam Coil Damper System To Replace PistonTo Replace Steam Coil To Replace the Needle ValveTo Replace the 3-WAY Microvalve To Replace Oven Contactor Electrical Oven ControlsTo Replace Electrical Elements Thermostats and Temperature Sensor To Replace HI-LIMIT Thermostat 330º GAS, 290º ElectricSail Switch Assembly GAS and Electric Models To Replace Sail SwitchFront Panel and Main Door Assemblies To Adjust Sail SwitchTo Replace Main Door Switch To Replace Front Panel To Replace Main Door AssemblyTo Install NEW Main Door Glass To Replace Main Door Hinge To Replace the Nylon CatchTo Replace Tumbler Pulley Reversing Tumbler and Bearing AssemblyTo Replace Tumbler Pulley NON-REVERSING To Replace the Rear Tumbler Bearing To Replace the Front Tumbler BearingTo Replace Idler Bearing Idler and Bearing AssemblyTo Replace Idler Pulley Drive Pulley Tumbler Alignment VerticalTumbler Alignment Lateral To Replace the Tumbler AND/OR Tumbler Support Belt Tension Alignment Motor to Idler Belt Tension Adjustment Tumbler to IdlerBelts To Replace V-BELTS MotorImpellor To Replace Motor NON-REVERSINGLint Drawer Screen To Replace Lint ScreenTroubleshooting Phase 7 NON-COIN System Diagnostics Diagnostic L.E.D. Display Fault MessagesINPUT/OUTPUT Board Light Emitting Diode L.E.D. Indicators American Dryer Corp 450268-1 Display reads Exhaust High Limit Fault. Refer to Display reads Sail Switch Closed Fault. Refer to 450268-1 Display reads Cycle Paused, Main Door Open. Refer to 450268-1 American Dryer Corp 450268-1 450268-1 American Dryer Corp 450268-1 450268-1 American Dryer Corp 450268-1 450268-1 Data Label Information Data LabelUsing a Manometer HOW to USE a ManometerKeypad Layout System Reset NON-COIN S.A.F.E. System Check ProcedureStatic Pressure ILLUS. #1ILLUS. #3 Using a MagnehelicILLUS. #2 American Dryer Corp 450268-1 450268-1 ADC Part No 1 10/26/05

AD-25, AD-30 specifications

American Dryer Corporation (ADC) has long been a trusted name in the commercial laundry equipment industry. Among their notable offerings are the AD-30 and AD-25 dryers, which are engineered to provide exceptional performance, reliability, and efficiency.

The AD-30 dryer is designed for high-capacity laundry operations, making it an ideal choice for large businesses such as hotels, hospitals, and laundromats. With a maximum drying capacity of 30 pounds, the AD-30 features a robust construction that can withstand the demands of heavy usage. Its powerful airflow technology ensures quick drying times, improving productivity and minimizing energy consumption. The dryer is equipped with a microprocessor control that offers multiple cycle options and customizable settings, allowing operators to tailor each drying cycle based on the specific fabric types being processed.

On the other hand, the AD-25 serves smaller operations with a capacity of 25 pounds, making it an efficient choice for businesses with moderate laundry needs. Similar to the AD-30, it incorporates advanced airflow technology to enhance drying efficiency. The AD-25 also features easy-to-use controls and programmable settings, providing flexibility for various drying requirements. Both models come with an easy-to-clean lint filter that helps maintain optimal air quality and prolongs the life of the machine.

In terms of construction, both dryers are built with durability in mind. Their stainless steel exteriors are not only aesthetically pleasing but also resistant to corrosion, ensuring they remain in good condition over time. The design of these dryers incorporates vibration reduction systems to minimize noise during operation, contributing to a more pleasant working environment.

Energy efficiency is a hallmark of American Dryer Corp products, and both the AD-30 and AD-25 are no exception. They are designed to consume minimal energy while delivering maximum drying performance, which can lead to significant cost savings over time. Additionally, the dryers are engineered with safety features, including over-temperature protection and a non-reversible door to prevent accidents.

In summary, American Dryer Corp's AD-30 and AD-25 dryers exemplify the brands' commitment to providing quality, efficiency, and reliability in commercial laundry operations. With their advanced technologies and user-friendly features, these dryers are well-equipped to meet the diverse needs of the laundry industry.
Top Page Image Contents