Whirlpool 3LTE5243BN0, 50 Hz Panel, Use new hoses and washers that came with your washer/dryer

Page 4

4 1

Insert a

-w/

rear-

leveling leg into the hole in

the rear corner on the

bottom

of the

 

washer/dryer.

Push leg in

until it snaps into place. Do the same same thing with the other leveling leg in the other rear corner.

5 n Push up one leg: check to see that the other leg goes down. Check the other leg the same way. (If legs do not adjust, repeat Step 4.)

6 n With one of the front legs in hand, check the ridges for a diamond marking. That’s how far the leg is supposed

to go into the hole. Start to screw the legs into the holes in the front corners by hand.

A

h

Numbers correspond to steps.

Do Not

9 Remove

H Remove the two

rear

Use slip-joint pliers to finish turning the front legs until you reach the diamond mark.

Slide washer/dryer onto cardboard or hardboard before movlng across floor to prevent damage to floor coverlng.

rear corner posts located at the back of the washer/dryer. Remove the two corner pieces attached to the lower front of the washer/dryer. Do Not remove the foam shipping pieces between the washer and dryer until me washer/dryer is in place,

corner posts

12 n Remove yellow card. Take hoses out of basket. Place hoses with other parts.

n Place a piece of cardboard or hardboard in front of carton. Now stand the washer/dryer upright. Slide washer/dryer onto cardboard or hardboard.

10 H Move foam shipping pieces outward just enough to clear the washer lid. Open me washer lid. The latch under the dryer will hold lid

open.

H Release washer

lid by pushing up on latch. Close lid.

I

To prevent product damage, Do Not

remove corner posts inside the carton before cutting.

.

8 n With me corner posts in

place, cut the carton down one corner. Remove carton.

8. A

Panel

 

 

 

 

 

 

 

out

of washer.

 

 

\\ 3 shipping

straps

 

 

11n Read the yellow

 

 

card. Place hand on top of

 

 

agitator

when

removing

the

 

 

shipping

straps. Firmly

jerk,

 

 

then

pull

the

three

shlpplng

L

three

straps up

until

each

strap

 

shipping

with

key

is completely

 

 

 

%

straps

 

 

 

with keys

removed from washer, Put v

 

straps in the same area as

 

 

other

shipping

pieces.

 

 

/

 

 

 

 

 

 

 

 

 

Numbers corresponc to steps.

Use new hoses and washers that came with your washer/dryer.

coupling washer

14 n Insert a large washer into each end of the inlet hoses. Check that washers are firmly seated in couplings.

Inlet valves are plastic. Do Not overt1 hten or crosst it read.

n Attach inlet hose to bottom

inlet valve opening first. Attach second inlet hose to top inlet valve. Tighten couplings by hand; then use pliers to make an additional two-thirds turn. Do Not overtlghten; this could cause damage to coupling.

Image 4
Contents InSkrllation sfrucfions Before you start Electrical requirementsObserve All governing Codes Ordinances Panel aMobile home installation Exhaust reauirementsNow start With washer/dryer in laundry areaUse new hoses and washers that came with your washer/dryer PanelThree Shlpplng Panel D Floor drain systemDo Not overtlghten this could cause Damage to couplerProduct dimensions Closet installationInstallation ’ -ITWasher/dryer By Whirlpool Corporation, Benton Harbor, MichiganPrepared 49022