Whirlpool 3406876 manual Washer USE, Understanding Washer Cycles, Loading, Normal Washer Sounds

Page 7

WASHER USE

Understanding Washer Cycles

When the Cycle Control knob is set to a number and pulled out, the washer fills (to the selected load size) before agitation and timing start. The washer begins agitating immediately after filling; agitation occurs with the washer lid up or down.

During agitation, the agitator creates a continuous rollover action (on some models) that provides a thorough cleaning of the wash load.

After agitation starts, the Cycle Control knob turns clockwise until it points to an OFF area and the cycle ends.

NOTE: The washer pauses briefly throughout each cycle. These pauses are normal for washer operation.

WASHRINSE

1. Fill

1. Fill

2. Wash

2.

Rinse

 

selected

 

 

 

time

 

 

3.

Drain

3. Drain

 

No agitation

 

No agitation

4.

Spin

4.

Spin-Spray

 

 

 

rinse

5. Spin

The Permanent Press cycle

6. Off

partially drains, fills, agitates

 

briefly, and drains.

 

 

 

Loading

Loading suggestions

For these suggested full-sized loads, set the WATER LEVEL selector to the highest setting.

Larger Capacity Washers

Heavy Work Clothes

Towels

2 pants

8 bath towels

3 shirts

8 hand towels

3 jeans

10 wash cloths

1 coverall

1 bath mat

Mixed Load

Permanent Press

2 double sheets

1 double sheet

4 pillowcases

1 tablecloth

6 T-shirts

1 dress

6 pair shorts

1 blouse

2 shirts

2 slacks

2 blouses

3 shirts

6 handkerchiefs

2 pillowcases

Delicates

Knits

2 camisoles

2 slacks

4 slips

2 blouses

6 undergarments

4 shirts

2 sets of sleepwear

4 tops

1 child’s outfit

2 dresses

Normal Washer Sounds

Your new washer may make sounds your old one didn’t. Because the sounds might be unfamiliar, you may be concerned about them. These sounds are normal.

During washing

When you select a small load size setting, your washer has a lower water level. This can cause a clicking sound from the upper part of the agitator.

During drain

If water is drained quickly from your washer (depending on your installation), you may hear air being pulled through the pump during the end of draining.

After drain and before spin

When the cycle changes from draining to spinning, you may hear gears engaging.

7

Image 7
Contents 3406876 Use & Care GuideTable of Contents Your safety and the safety of others are very important WASHER/DRYER SafetyImportant Safety Instructions Other features Parts and FeaturesControl panel Checking Your Vent Normal Washer Sounds Washer USEUnderstanding Washer Cycles LoadingCold StartingYour WasherWater Temp Use For Hot WarmAdding Liquid Chlorine Bleach Selecting aCycle and TimeRinse and Spin Drain and SpinTo stop your dryer Dryer USEStartingYour Dryer Stopping and RestartingCycle Descriptions Drying,Cycle and Temperature TipsWaterInlet Hoses End of Cycle SignalCleaning YourWasher Cleaning the Lint ScreenRemoving Accumulated Lint Cleaningthe Dryer InteriorVacation, Storage,and MovingCare Troubleshooting Washer Load is tangled or twisted Did you overload the washer? Residue or lint on load Did you sort properly?Did you overload the washer? Did you unload the washer promptly?Troubleshooting Dryer For further assistance Assistance or ServiceIf you need replacement parts To locate FSP replacement parts in your area3406876 Whirlpool Corporation will not pay for