Connecting Your Loudspeakers Figures 5 | Polk Audio CSi 20, FXI50

Diffuse surround effects—di-pole mode [figure 4]: For a more diffuse effect, place the speakers on the side walls in line with your listening position and at least 2 feet away from the rear wall. Select the “dipole” switch setting [figure 2].

Processor Mode Configuration for the FXi Series Surround FX Loudspeaker: Set Surrounds to “Small” in your receiver’s Bass Management settings.

CONNECTING YOUR LOUDSPEAKERS [FIGURES 5 & 6]

We recommend 16-gauge or larger speaker wire. Follow the hookup directions included with your receiver. Strip 1/2 inch (12.7mm) of insulation from each of the two conductors of the wire to expose the bare metal and twist each of the individual conductors into single unfrayed strands. Note that one of the terminals on the rear of each speaker is red (+) and the other is black (-). Make certain that you connect the wire from the red (+) terminal of your amplifier or receiver to the red (+) terminal on your speaker and the wire from the black (-) terminal of your amplifier or receiver to the black (-) terminal on your speaker. Most wire has some indicator (such as color-coding, ribbing or writing) on one of the two conductors to help you maintain consistency.

To connect wire to the binding post [figure 7], unscrew the hex nut and insert the bare wire into the hole near the base of the binding post. Do not insert the insulated part of the wire into the hole as this will not give you a good connection. Twist the hex nut back down the binding post until it firmly meets the wire. Do not over tighten.

To use Banana Plugs (US only): Unscrew the binding post lug nuts completely to expose the binding post plugs (plastic plugs inserted into the binding posts). Carefully pry out the binding post plugs to expose banana plug holes. Screw the lug nuts back on the binding posts and insert banana plugs. (This is for US owners only.)

BI-WIRING OR BI-AMPING THE CSi40

If you decide to bi-wire or bi-amp, you must remove the flat metal jumpers between terminal posts. Failure to do this could result in damage to your amplifier and loudspeakers.

Bi-wiring [figure 8] can provide noticeable improvements in the overall transparency of your loudspeakers. Run separate speaker wires to the low and high frequency drivers from a single amplifier: after removing the jumpers, connect one set of speaker wires to the upper terminals on each speaker and one set of (usually heavier gauge) wires to the lower terminals. Connect the other ends of both wire sets to the corresponding amplifier outputs.

FOR MANUAL UPDATES, VISIT

http://www.polkaudio.com/home/library/manuals.php

FOR MORE DETAILED HOOK UP AND PLACEMENT INFORMATION, VISIT

http://www.polkaudio.com/home/faqad/

FOR RECOMMENDED ACCESSORIES (INCLUDING SPEAKER STANDS, BRACKETS AND EXCLUSIVE POLK AUDIO LOGOWEAR), VISIT OUR WEBSTORE: http://shop.polkaudio.com/

Contact Polk Audio Customer Ser vice 1 - 800 - 377 - 7655 (Outside US: 410 - 358 - 3600), polkcs@polkaudio . com

CSi 20, CSi 30, FXI50, CSi 40, FXI30 specifications

Polk Audio has long been known for its commitment to high-quality sound and innovative audio technology. Among its impressive lineup of speakers, the FXI30, CSi 40, FXI50, CSi 30, and CSi 20 stand out for their distinct features and performance capabilities.

Starting with the FXI30, this surround speaker is designed to deliver immersive audio experiences for home theater setups. One of its key features is the unique design that allows it to be mounted on walls, making it versatile for various room layouts. The FXI30 utilizes a dual-driver configuration along with a dual-port system, effectively enhancing dynamic range and clarity. Its 90-degree design helps disperse sound widely, creating a more enveloping listening experience, making it a favorite for movie enthusiasts.

The CSi 40 is a center-channel speaker built to anchor your home theater system. It boasts dual 5.25-inch dynamic balance drivers paired with a 1-inch silk dome tweeter, delivering crisp dialogue and a rich audio spectrum. This speaker excels in reproducing voices clearly, ensuring that every word is heard, even during the most explosive scenes in films. The CSi 40 is also designed to minimize distortion, allowing for extended listening sessions without fatigue.

The FXI50 takes the surround sound experience to the next level with its enhanced power and performance. Featuring larger drivers compared to the FXI30, it utilizes advanced Dynamic Balance technology, which ensures accurate sound reproduction across the frequency spectrum. The tri-pole design offers more flexibility in placement and creates a wider soundstage, making it an ideal choice for those seeking an immersive audio experience.

For those looking for a smaller yet effective solution, the CSi 30 is a compact center speaker designed for smaller rooms or setups. It features dual 5.25-inch drivers for a powerful audio performance despite its size and a 1-inch tweeter for enhanced high-frequency reproduction. Its sleek design allows it to blend seamlessly with modern décor while delivering substantial sound quality.

Lastly, the CSi 20 is a versatile entry-level center speaker that holds its ground with impressive features. Like its CSi counterparts, it includes Dynamic Balance drivers and a silk dome tweeter for clear highs and rich mids. It is perfect for those who wish to upgrade their home audio experience without compromising on quality.

In summary, Polk Audio’s FXI30, CSi 40, FXI50, CSi 30, and CSi 20 each offer unique features and technologies that cater to various home theater needs. From immersive surround sound capabilities to crystal-clear dialogue reproduction, these speakers are designed with quality and performance in mind. Whether you are a movie enthusiast or a casual listener, these speakers promise to elevate your audio experience to new heights.