Pelco TXB-V manual Spectra Mini Dome Installation

Page 14

Spectra Mini Dome Installation

To install the TXB-V translator board in a Spectra Mini dome:

NOTE: Installing a TXB-V into a mini dome increases unit height. In surface mount installations, you must cut a hole in the surface to accommodate the TXB-V cover. For an installation template and more information, refer to the Spectra Mini Dome Installation manual.

1.Turn off power to the dome system.

2.If the Spectra Mini dome is already installed, remove it to access the top of the dome drive where the translator board will be installed.

3.Place the dome drive on a flat surface with the dome liner pointing up.

4.Set the DIP switches on the dome (refer to Figure 12 for switch location): NOTE: There are no SW1 switch settings on the Spectra Mini dome.

a.Point the camera straight up.

b.Using a flashlight, look through the viewing slot of the dome liner. Rotate the dome liner until you see two DIP switches in the bottom of the housing.

ON

SW 3

SW 2

ON

 

Figure 12. Locating the Spectra Mini Dome DIP Switches

c.SW2: Set all switches to the OFF position.

d.SW3: Set the Spectra Mini dome address (refer to Table A on page 24 of the Appendix for switch settings).

14

C656M-E (4/07)

Image 14
Contents Translator Board Contents Important Safety Instructions Important NoticeRegulatory Notices Radio and Television InterferenceParts List DescriptionEsprit Installation SW1 Set all SW1 switches to the OFF position BaudInstalling the Esprit Cover Vicon Controller Esprit Terminal Block J1 Wire Harness TOP Gasket Front Rain GuardSpectra III/Spectra IV Installation Spectra III/Spectra IV Back Box Interconnect Door Vicon Controller Spectra III/SpectraRemove Shorting Plug PIN Connector Standoff SW3 Spectra Mini Dome Installation Baud Installing the TXB-V and Mini Dome Cover Response Out + ExSite Installation ExSite Spanner WrenchBaud Vicon Controller ExSite Terminal Block J1 Wire Harness SW1SW3Operation Special Functions DefinitionsTXB-V Zone Programming Procedure Step ProcedureTroubleshooting Symptom Possible Cause Suggested RemedyTable A. Receiver Address Settings AppendixTable A. Receiver Address Settings 100 118 158 198 Revision History Product Warranty and Return Information ISO9001

TXB-V specifications

The Pelco TXB-V is a prominent model in the realm of surveillance technology, specifically designed to meet the demanding needs of security professionals. As a part of the TX series, this camera is specifically engineered for high-performance applications, making it an ideal choice for various environments including retail, transportation, and critical infrastructure.

One of the main features of the Pelco TXB-V is its advanced imaging capabilities. It typically incorporates a high-resolution image sensor that delivers exceptional video clarity, enabling users to capture detailed footage even in challenging lighting conditions. With its ability to perform well in both daylight and low-light environments, the TXB-V is equipped with a robust infrared (IR) technology, allowing for quality night vision without compromising image integrity.

Another key characteristic of the TXB-V is its versatility. The camera supports multiple resolutions and frame rates, which provides flexibility in terms of storage and bandwidth management. Users can configure the settings according to their specific needs, ensuring optimal performance in various scenarios. Furthermore, the TXB-V is often designed with a weather-resistant housing, making it suitable for outdoor applications whether it be rain, snow, or extreme temperatures.

The TXB-V also boasts advanced video analytics capabilities, which significantly enhance the surveillance experience. This includes features such as motion detection, tamper detection, and line crossing detection. These analytics empower users by allowing them to receive alerts and notifications when unusual activities are detected, effectively enhancing site security.

In terms of connectivity, the Pelco TXB-V typically supports multiple networking options including Power over Ethernet (PoE). This simplifies installation and reduces the need for additional wiring, enabling a more straightforward deployment in various settings. The camera's compatibility with both IP systems and traditional analog systems further extends its applicability across different security infrastructures.

Overall, the Pelco TXB-V combines cutting-edge technology with robust features to deliver an effective surveillance solution. Its high-definition imaging, advanced analytics, weatherproof design, and versatile connectivity make it an excellent choice for anyone seeking to enhance their security infrastructure with reliable and efficient surveillance technology.