Bush Hog RDTH 84 EMPLOYERS, Employees and Operations, Employee Tractor Operating Instructions

Page 8

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING

EMPLOYERS, EMPLOYEES AND OPERATIONS.

*(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such).

U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA

This Act Seeks:

“...to assure so far as possible every working man and woman in the nation safe and healthful working conditions and to preserve our human resources...”

DUTIES

Sec. 5 (a) Each employer—

(1) shall furnish to each of his employees employment and a place of employment which are free from recognized hazards that are causing or are likely to cause death or serious physical harm to his employees;

(2)shall comply with occupational safety and health standards promulgated under this Act.

(b)Each employee shall comply with occupational safety and health standards

and all rules, regulations and orders issued pursuant to this Act which are applicable to his own actions and conduct.

OSHA Regulations

Current OSHA regulations state in part: “At the time of initial assignment and at least annually thereafter, the

employer shall instruct every employee in the safe operation and servicing of all equipment with which the employee is, or will be involved.” These will include (but are not limited to) instructions to:

Keep all guards in place when the machine is in operation;

Permit no riders on equipment;

Stop engine, disconnect the power source, and wait for all machine movement to stop before servicing, adjusting, cleaning or unclogging the equipment, except where the machine must be running to be properly serviced or maintained, in which case the employer shall instruct employees as to all steps and procedures which are necessary to safely service or maintain the equipment.

Make sure everyone is clear of machinery before starting the engine, engaging power, or operating the machine.

EMPLOYEE TRACTOR OPERATING INSTRUCTIONS:

1.Securely fasten your seat belt if the tractor has a ROPS.

2.Where possible, avoid operating the tractor near ditches, embankments, and holes.

3.Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.

4.Stay off slopes too steep for safe operation.

Child Labor Under 16 Years Old

5.Watch where you are going, especially at row ends, on roads, and around trees.

6.Do not permit others to ride.

7.Operate the tractor smoothly - no jerky turns, starts, or stops.

8.Hitch only to the drawbar and hitch points recom- mended by tractor manufacturers.

9.When tractor is stopped, set brakes securely and use park lock if available.

Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.)

6

Image 8
Contents Bush HOG Congratulations Table of Contents RdthThis Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List Rdth Rotary CutterIs Involved White letters onRED OrangeImportant Safety Precautions EMPLOYERS, Employees and Operations Employee Tractor Operating InstructionsSec a Each employer Securely fasten your seat belt if the tractor has a RopsSection IntroductionDescription Introduction and DescriptionSecurely Block Cutter in Position Attaching to TractorPreparation for USE Repeat steps G and H to other driveline sec- tion This allows cutter to float during operationGeneral Safety Cutting Height AdjustmentOperating Instructions OperationMaintenance Check List LubricationBefore Each USE After Each USEBelt Adjustment Blade ReplacementBelt Replacement FrontTroubleshooting Problem Probable Cause RemedySection Dealer Assembly Page Safety Decals 50042283 7860883056 50042281 50042285 50042282 50012616 78786SAE Grade Dashes Torque SpecificationsSAE Grade No Dashes
Related manuals
Manual 28 pages 25.64 Kb