Pioneer DEX-P90RS owner manual CD Player and Care / Connecting the Units

Page 81

Connecting the Units

Note:

•This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recre- ational vehicle, truck, or bus, check the battery voltage.

•To avoid shorts in the electrical system, be sure to disconnect the ≠ battery cable before beginning installation.

•Refer to the owner’s manual for details on con- necting the power amp and other units, then make connections correctly.

•Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

•Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake, and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insu- lation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body.

•Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short.

•Do not shorten any leads. If you do, the protection circuit may fail to work when it should.

•Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

•When replacing a fuse, be sure to use only fuses of the rating prescribed on the fuse holder.

•The black lead is ground. Please ground this lead separately from the ground of high-current prod- ucts such as power amps.

If you ground the products together and the ground becomes detached, there is a risk of dam- age to the products or fire.

•When this product’s source is switched ON, a control signal is output through the blue/white lead. Connect to an external power amp’s system remote control or the car’s Auto-antenna relay control terminal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the anten- na booster power supply terminal.

•When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal. Likewise, do not connect the blue/white lead to the power ter- minal of the auto-antenna. Such connection could cause excessive current drain and malfunction.

•To avoid short-circuiting, cover the disconnected lead with insulating tape. There is a possibility of short-circuiting if the leads are not insulated.

•To prevent incorrect connection, the input side of the IP-BUS connector and Optical connector is blue, and the output side is black. Connect the connectors of the same colors correctly.

•Connection of this system requires optical cables and IP-BUS cables. Consult your nearest dealer for more detail.

•Set GPS antenna away from this unit. If you set them too close, it may fail to operate properly.

•This unit can not be installed in a vehicle that does not have an ACC (accessory) position on the ignition switch. (Fig. 1)

 

 

CC

 

 

 

 

 

 

 

 

 

F

A

O

 

 

 

F

O

 

 

 

 

N

 

F

N

O

F

 

 

 

 

O

 

 

 

 

 

 

 

S

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T

 

 

 

 

T

 

 

 

 

R

A

 

 

 

R

A

 

 

 

T

 

 

 

T

 

 

 

 

 

 

 

 

 

 

ACC position

No ACC position

Fig. 1

•Cords for this product and those for other prod- ucts may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the

same function.

CD Player and Care / Connecting the Units

80

Page 80 Page 82
Image 81
Page 80 Page 82
Contents DEX-P90RS Contents Tuner Operation ContentsInstallation Contents / Key Finder Remote ControlKey Finder Head UnitOpening and Closing the Remote Control Cover When the Cover is Open When the Cover is ClosedMenu display in closed state Menu display in open stateUsing the Remote Control Remote Control and CareBatteries Resetting the Microprocessor Before Using This ProductAbout This Product About This ManualBefore Using This Product PrecautionTheft Protection Detaching and Replacing the Front PanelDetaching the Front Panel Open the front panelDetaching and Replacing the Front Panel Replacing the Front PanelSetting Up the Environment for Use Setting Up the Environment for UseOperation at the Initial Setting Screen Accessing the Initial Setting ScreenExit from the Initial Setting Screen Switching to the Clock Adjustment Screen Setting the ClockSetting the Clock Press the Function button 1 on Initial Setting ScreenReturns to the Initial Setting Screen Setting the Clock by Time SignalOff Clock Press the Return buttonSwitching to the Display Setting Screen Setting the DisplaySetting the Brightness Setting the DimmerSelecting the Wallpaper Selecting the Reverse ModeSwitching to the General Environment Setting Screen Setting the General EnvironmentSwitching the AUX Mode Setting the Warning ToneWhen it is on Setting the DAB PriorityWhen it is OFF Turning the Confirmation Sound ON/OFFChanging the FM Tuning Step Switching the Auto PI SeekSetting the Menu Lock Switching to the Menu Lock ON/OFFAbout the Menu Lock Basic Operation Remote ControlTo Listen to Music Select the desired source e.g. tunerRaise or lower the volume Switching Power OFFTurn the source OFF Basic OperationBasic Operation of Tuner Tuner OperationAccessing the Tuner Setting Screen Operation at the Tuner Setting ScreenExit from the Tuner Setting Screen Tuner Setting ScreenLocal Seek Tuning Operating Each functionBest Stations Memory Preset Tuning Switching to the Preset Tuning ScreenPress the Shift button on Tuner Setting Screen Broadcast station preset memoryWhat is RDS? Using the RDS FunctionsAlternative Frequency function Activating/Deactivating the AF functionUsing the RDS Functions Auto PI Seek for preset stationPI Seek function PI SeekTo cancel the PTY Search, press the ∞ button PTY functionSearching the PTY PTY Alarm News Program Interruption SettingCanceling Announcements Set interruption to on or OFFWide Narrow Details PTY ListActivating/Deactivating the TA function Traffic Announcement Standby functionTune in a TP or enhanced other network’s TP station Activate the TA functionCanceling Traffic Announcements Adjusting the TA VolumeTP Alarm function Activating the Regional function Regional functionTo return to Tuner Setting Screen, press the Return button Radio TextRadio Text Display Storing Radio Text in Memory Recalling Preset Radio TextBuilt-in CD Player Operation Basic Operation of Built-in CD PlayerEject CD Loading Slot Track Search and Fast Forward/ReverseOpen Built-in CD Player OperationAccessing the Built-in CD Setting Screen Operation at the Built-in CD Setting ScreenExit from the Built-in CD Setting Screen Built-in CD Setting ScreenRandom Play Repeat PlayPause Scan PlayDisc Title Input Changing the Display ModeBasic Operation of Multi-CD Player Multi-CD Player OperationAccessing the Multi-CD Setting Screen Operation at the Multi-CD Setting ScreenExit from the Multi-CD Setting Screen Multi-CD Setting ScreenDisplay Play range Play ModeRandom Play Disc Number Search Press the Shift button on Multi-CD Setting ScreenSwitch the desired character type with Function button Select letters, numbers and symbols with the 5/∞ buttonsDisc Title Multi-CD Player Operation Selecting Discs by Disc Title List Play Time Indicator Disc Search Title Indicator Disc Number IndicatorDVD Player Operation Basic Operation of DVD PlayerAccessing the DVD Setting Screen Operation at the DVD Setting ScreenExit from the DVD Setting Screen DVD Setting ScreenVideo-CD and CD DVDOperable only when DVD Player is playing CDs Select the desired disc with the Function button 1 through Press the Shift button on DVD Setting ScreenService Label Band Indicator Selecting the Ensemble or ServiceDAB Tuner Operation Basic Operation of DAB TunerAccessing the DAB Tuner Setting Screen Operation at the DAB Tuner Setting ScreenExit from the DAB Tuner Setting Screen DAB Tuner Setting ScreenDAB Tuner Operation Press the Shift button on DAB Tuner Setting ScreenAnnouncements operated by the TA button Announcement Support functionTP Alarm function Operating Announcements with DAB Tuner Setting Screen Service Component function Switching Interrupting AnnouncementsSwitch to the next Announcement Dynamic Label function Dynamic Label DisplayScroll the Dynamic Label with the ∞ button Storing Dynamic Label in Memory Recalling Preset Dynamic LabelCanceling the PTY Search Setting mode Available PTY functionSearching the PTY Service Follow function Service Follow function FMWhen the NET indicator flashes Channel Indicator Preset Number Indicator Band Indicator TV Tuner OperationBasic Operation of TV Tuner Accessing the TV Tuner Setting Screen Operation at the TV Tuner Setting ScreenExit from the TV Tuner Setting Screen TV Tuner Setting ScreenBest Stations Sequential Memory Press the Shift button on TV Tuner Setting Screen Switching to the Audio Adjustment Screen Audio AdjustmentFader/Balance Adjustment To cancel the Audio Adjustment, press the Band buttonBass/Treble Adjustment Press the 5/∞ buttons and adjust the levelAudio Adjustment Increase or decrease the level with the 5/∞ buttons Source Level AdjustmentOther Functions Using the AUX SourceSound Muting Selecting the AUX SourceTurn OFF the Display Indication CD player and care CD Player and CareCD-R/CD-RW discs Other Functions / CD Player and CareMessage Possible cause Recommended action Built-in CD Player’s Error MessageCD Player and Care / Connecting the Units Connecting the UnitsSetting Examples Connecting without Audio Unit DEQ-P90Connecting with Audio Unit DEQ-P90 Attaching the Noise Filter Connecting the UnitsConnecting without Audio Unit DEQ-P90 Left Right Connecting with Audio Unit DEQ-P90 Power amp Sold separately Installation with the rubber bush InstallationRemoving the Unit InstallationFitting the Remote Control Unit Installing the Remote Control UnitInstallation Using Only the Mounting Base Fitting horizontally Fitting verticallyInstalling the Remote Control Unit Installation Using the Mounting Base and the BracketMethod a Method BInstall the mounting base to the vehicle Install the bracket to the mounting baseSpecifications Pioneer Corporation
Top Page Image Contents