Standard Horizon CP180I, CP500, CPV550, CP300 MBS Main Bang Suppression Adjustment, Automatic Tune

Page 13

12.Move the ShuttlePoint knob down to highlight MBS and adjust to 000 by moving the ShuttlePoint knob to the right.

13.Move the ShuttlePoint knob down to highlight TX TRIGGER DELAY and adjust moving the ShuttlePoint knob to the right to a point that the center looks as a solid circle as shown in the diagram below.

14.To save the TX Trigger Delay setting, move the ShuttlePoint knob down to Done and press [ENT].

098

Figure 3.1.0c - Adjusting Trigger Delay

MBS (Main Bang Suppression) Adjustment

(ONLY FOR MDS-9 DOME & MDS-10-4/MDS-10-5 OPEN ARRAY ANTENNAS)

The MBS is used to remove the echo closest to the vessel as shown in the right image in figure 3.1.0c. If Main Bang appears at the screen center (it looks like a as a circular dot) suppress it as follows:

1.Transmit on a long range about ten minutes.

2.Press [MENU]. Move the ShuttlePoint knob to highlight TUNING and press [ENT].

3.Move the ShuttlePoint knob to highlight TX TRIGGER DELAY and press [ENT].

4.Move the ShuttlePoint knob to highlight GAIN and press [ENT]. Adjust the Gain in such a way that the circular dot is clearly displayed.

5.Move the ShuttlePoint knob to highlight MBS and press [ENT]. Increase the MBS value until the circular dot is completely erased from the screen. Do not increase the MBS more than the value required to completely erase the main bang it otherwise you run the risk to suppress also target echoes.

3.1.1Automatic Tune (NOT NECESSARY AT FIRST INSTALLATION)

The Tune control is used to tune the receiver in the Radar antenna for maximum target returns on the display. The Radar comes from the factory already tuned so this operation is not necessary at first installation. In general Radar tuning may be necessary if the Radar antenna was serviced.

Automatic Tune

In Automatic Tune mode, the Radar tunes itself automatically on all range scales. It is recommended to execute the Tune function in Automatic mode. This generally ensures that the Radar receiver is always tuned to receive the maximum signal.

After the Radar Antenna is installed (or has been on the vessel for a year or longer) perform the Automatic Tune procedure, which adjusts the receiver Gain to show targets on all ranges.

Radar Operation Manual

 

Page 15

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Page Code Issue a 160108e Table of Contents Troubleshooting Frequently Asked Questions Index Conventions Used IntroductionIntroduction General Information Product Support InquiriesPage Radar Pages Selecting page Using Soft KEY Except CP180/CP180iDisplaying the Radar Pages Soft KEY Operation in Radar page Except CP180/CP180i Customizing the Soft KeysTransmit Soft Key Gain Soft Key Range Soft KeyRain Soft Key SEA Soft KeySelection of active window Warming UP OperationsTransmission Trigger Delay SET UPAutomatic Tune MBS Main Bang Suppression Adjustment1 AutomaticTune Save Tuning to User C-CARDHeading Line Load Tuning from User C-CARD4 Heading Line Antenna Parking PositionSector Transmission Off 5 Antenna Position settingPage Radar Window Understanding the Radar DisplayCursor BasicEcho Trails Motion ModeTarget Expansion Heading Marker Cursor WindowRange Rings Degree ScaleStatus Bar Except CP180/CP180i Compass RoseSensitivity Gain AdjustmentInterference Rejection Sea Clutter 1 Gain AdjustmentRain Clutter FeaturesOrientation EBL & VRMHook Handling of EBL & VRMCenter Offset Parallel CursorUser Points Handling of Center OffsetAIS Targets Chart Overlay Chart FeaturesData Window only for CP180/CP180i 0 Chart Overlay Chart Synchronization Except CP180/CP180iColor Palette Cursor Echo Except CP180/CP180iGuard Zones Guard Zone Sensitivity Handling of Guard ZonePage Radar page is not available TroubleshootingRadar sensitivity appears to be low What should I do at first Radar installation? Frequently Asked QuestionsWhat is SEA clutter STC, and how should it be used? What are Guard Zones? Page Active Window IndexPlease Note
Related manuals
Manual 100 pages 33.72 Kb Manual 92 pages 12 b Manual 89 pages 4.24 Kb

CP300, CP180, CP180I, CP500, CPV550 specifications

Standard Horizon is well known for its innovative marine electronics, particularly its line of chart plotters and multifunction displays. Among its popular products are the CPV550, CP500, CP180I, CP180, and CP300 models, each designed to enhance navigational experience for boaters and sailors.

The Standard Horizon CPV550 is a cutting-edge chart plotter that features a bright, high-resolution 5.5-inch color display. This model supports Navionics and C-MAP charts, ensuring users have access to high-quality cartography. Its built-in GPS receiver offers exceptional accuracy and fast position fixes, while its user-friendly interface allows for easy navigation through menus and functions. The CPV550 is equipped with a variety of connectivity options, including NMEA 0183, allowing for seamless integration with other onboard electronics.

The CP500 is another robust option, featuring a 5-inch display and advanced GPS technology. This model is designed for ease of use, with a straightforward interface that appeals to both novice and experienced users. It offers real-time tracking and position monitoring, making it ideal for coastal cruising and fishing. The CP500 supports various cartography formats, providing flexibility for users who prefer different map sources.

Moving on, the CP180I model stands out with its innovative integrated design, packing a 7-inch display and multiple advanced features into a compact unit. It includes built-in Wi-Fi, allowing users to connect their mobile devices and access updates or weather information directly from the display. The CP180I is also compatible with a wide range of NMEA 2000 devices, offering greater customization options for boaters looking to expand their electronic setups.

The CP180 offers similar capabilities but focuses on a slightly larger 8-inch screen. This model enhances visibility and provides an intuitive experience with its touch-screen interface. It supports various navigation modes and features such as AIS overlay and radar integration, which significantly improve situational awareness on the water.

Finally, the Standard Horizon CP300 is a versatile chart plotter that combines advanced features with exceptional user-friendliness. This model features a 9-inch display that offers crisp visuals and enhanced readability even in bright sunlight. It also stands out for its robust integration capabilities with other marine instruments. The CP300 includes built-in Bluetooth and Wi-Fi, allowing for wireless data sharing and connectivity with smart devices.

Overall, the Standard Horizon line of chart plotters, including the CPV550, CP500, CP180I, CP180, and CP300, offers advanced technological features, reliable performance, and user-friendly interfaces, making them excellent choices for both leisure and professional mariners alike. With a focus on connectivity, visibility, and customizable options, these devices enhance the navigation experience on the water.
Top Page Image Contents