Ingersoll-Rand PD20P-X-X manual Service Kits, Pump Data, Model Description Chart, Weight

OPERATOR’S MANUAL	PD20P-X-X
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE	PE20P-X-X
2” DIAPHRAGM PUMP	RELEASED: 12-16-02
	REVISED: 10-9-10
1:1 RATIO (NON-METALLIC)	(REV. K)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS

Refer to Model Description Chart to match the pump material options. 637369 for air section repair (see page 6).

637373-XX for fluid section repair (see page 4). NOTE: This kit also con- tains several air motor seals which will need to be replaced.

637374-X major air valve assembly (see page 7).

PUMP DATA

Models	see Model Description Chart for “-XXX”.
Pump Type	Non-Metallic Air Operated Double Diaphragm
Material	see Model Description Chart.

Weight . . .	PX20P-FKS-XXX	110.9 lbs (50.3 kgs)
	PX20P-FPS-XXX	85.3 lbs (38.7 kgs)
Maximum Air Inlet Pressure		120 p.s.i.g. (8.3 bar)
Maximum Material Inlet Pressure		10 p.s.i.g. (.69 bar)
Maximum Outlet Pressure		120 p.s.i.g. (8.3 bar)
Maximum Flow Rate (flooded inlet) . . . .		184 g.p.m. (696 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g. . . .		1.4 gal. (5.3 lit.)
Maximum Particle Size		1/4” dia. (6.4 mm)

Maximum Temperature Limits (diaphragm / ball / seal material)

E.P.R. / EPDM	. . . . -60_to 280_F (-51_to 138_C)
HytrelR	. . . . -20_to 150_ F (-29_to 66_ C)
Nitrile	. . . . 10_ to 180_ F (-12_to 82_ C)
Polypropylene	. . . . . .35_ to 175_ F (2_ to 79_ C)
KynarR PVDF	. . . . 10_ to 200_ F (-12_to 93_ C)
SantopreneR	. . . . -40_to 225_F (-40_to 107_C)
PTFE	. . . . 40_ to 225_ F (4_ to 107_ C)
VitonR	. . . . -40_to 350_F (-40_to 170_C)
Dimensional Data	. . . . . . . . . see page 8
Mounting Dimension	8.18” x 14.16” (207.8 mm x 359.7 mm)

Noise Level @ 70 p.s.i., 60 c.p.m. . . . . . 85.0 db(A){

The pump sound pressure levels published here have been updated to an Equivalent

Continuous Sound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEU- ROP S5.1 using four microphone locations.

NOTICE: All possible options are shown in the chart, however, certain combinations may not be recommended, consult a representative or the factory if you have questions concerning availability.

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET
BRYAN, OHIO 43506

Figure 1

MODEL DESCRIPTION CHART

P X 20 P - F X S - X X X

Electronic Interface

D - None

E - Available

Center Section Material

P - Polypropylene / Vinyl Ester

Fluid Connection

F - 2” A.N.S.I. / DIN Flange

Fluid Caps & Manifold Material

P- Polypropylene K - Kynar PVDF

Hardware Material

S - Stainless Steel

Seat Material

P- Polypropylene K - Kynar PVDF

Ball Material
A	- Santoprene	T	- PTFE
C	- Hytrel	V	- Viton
G	- Nitrile
Diaphragm Material
A	- Santoprene	M	- Medical Grade Santoprene
C	- Hytrel	T	- PTFE / Santoprene
G	- Nitrile	V	- Viton

FLUID SECTION SERVICE KIT SELECTION	PX20P - FXS - X X X
EXAMPLE: Model # PD20P-FPS-PAA	637373 - X X
Fluid Section Service Kit # 637373-AA	Ball	Diaphragm

(800) 276-4658 D FAX (800) 266-7016 E2010 CCN 20083440