PYLE Audio PYD 2200 warranty Presetting the Controls Before Use, Connecting the Mixer Inputs

Page 3

Presetting the Controls Before Use

Since sudden high output levels from your Pyle Pro mixer can damage not only audio devices connected to the mixer output but your hearing as well (especially if you are using headphones), please adjust the mixer’s controls BEFORE connecting AC power or turning on the unit.

Set up the mixer controls like this before you start:

CONTROL

SETTING

Power On/Off

OFF

Balance

MID

Gain

MID

Tone Controls, High, Mid & Low

0

MIC 1, CH 1/2/3/4/5, Master & Cue Levels

0

Crossfader

CENTER

Connecting the Mixer Inputs

Connecting High Level Output Audio Sources

Connect up to 9 such sources (tuner, cassette deck, CD Player, camcorder or VCR) to the input jacks for Line 1 , Line 2(if not being used as Phono 1 input), Line 3, Line 4(if not being used as Phono 2 input), Line 5, Line 6, Line 7, Line 8 and Line 9. Please note that Phono 1 and Line 2 (as well as Phono 2 and Line 4) use the same jacks. The selector switch(e)s below the jacks should be set to Line position if the jacks are used for the High Level input sources described here.

 

Use RCA type

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

patch cables

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CH 2

CH

 

V O LTA G E

 

OUTPUT

 

 

 

 

 

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

 

 

~AC INPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FUSE F 500mA

250V

BALANCED

Master

Booth

Rec

 

 

CH 5

 

CH 4

 

CH 3

 

 

 

 

CH 2

 

 

 

CH 1

L

L

L

 

 

 

L

 

 

L

L

 

 

 

 

 

 

L

L

 

 

 

L

 

L

GND

 

 

 

R

L

 

 

 

 

 

 

 

 

 

 

 

 

MIC 2

 

 

 

 

 

R

 

 

R

R

 

 

 

 

 

 

R

R

 

 

 

R

 

R

 

 

 

 

 

 

 

 

 

 

Line 9

Line 8

Line 7

Line 6

Line 5

Phono

2

LN 4

PH 2

Line 3

Phono

1

LN 2

PH 1

Line 1

R

R

R

 

 

 

 

 

 

 

 

 

 

 

 

/Line 4

 

 

 

 

/Line 2

 

 

 

 

 

 

 

This mixer permits connection of up to nine (9) audio input sources,and two microphones. Such a system might include, for example:

Two Microphones

Two Microphones

Two Microphones

Two Microphones

Two Turntables

Nine CD players

Two Turntables

Two Turntables

Seven CD players

 

Four CD players

Four CD players

 

 

 

Three Cassette Decks

One Rhythm Synth

 

 

 

 

Two Cassette Deck

 

 

 

Please observe

Do not connect any audio source with a HIGH LEVEL OUTPUT to the

LOW LEVEL PHONO 1 or PHONO 2 mixer audio input jacks (an audio

the following:

source output with a volume control is HIGH LEVEL).

 

 

High Level Output

Audio Source

LEFT output

RIGHT output

CD player, cassette deck, camcorder, VCR, etc.

PH 2 Line 3 Phono

1 LN 2

PH 1 Line 1

/Line

2

 

NOTE!

If you use a High Level Output Audio Source(s) in the Phono1/Line2 (and/or Phono2/Line4) input jack(s), be sure to place the Input Select switch in the LINE2 (and/or LINE4) position(s)!

Connecting Microphones

Microphone 1. Connect a balanced/unbalanced low impedance (600 Ohm) XLR type MIC OR a low impedance MIC with a 1/4” plug to the MIC 1 jack in the upper left corner of the mixer control panel.

 

MIC 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Gain

 

Gain

 

Gain

 

Gain

 

Gain

 

 

 

 

 

 

 

 

 

 

 

 

 

POWER

Use 1/4” or

MIC 1 Volume

 

 

 

 

 

 

 

 

 

 

Balance

 

 

 

 

 

 

 

 

 

 

 

 

XLR-type jack

 

Cue

 

Cue

 

Cue

 

Cue

 

 

Cue

 

High

High

 

High

 

High

 

High

 

High

 

Master

 

 

 

CH

 

CH

 

CH

 

CH

 

CH

 

MIC 1

Low

Mid

1

Mid

2

Mid

3

Mid

4

Mid

5

Booth

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connecting Turntables and Other Level Output Audio Sources

Connect up to 2 turntables to the Phono 1 and Phono 2 input jacks. Please note that Phone 1 and Line 2 (as well as Phono 2 and Line 4) use the same jacks. The selector switch below the jacks should be set to Phono position if the jacks are used for phono inputs.

When using a turntable, you should also securely connect its ground wire (usually green or black) to the Ground screw on the input panel of the mixer.

Use RCA type patch cables

Low

Low

Low

Low

Low

Cue Level

 

 

 

 

Mix

Headphones

 

ASSIGN A

 

 

CUE

PGM

 

 

 

ASSIGN B

 

C R O S S F A D E R

Microphone 2. Connect a high quality balanced/unbalanced low impedance (600 Ohm) microphone with a 1/4” plug to the MIC 2 jack on the lower left corner of the mixer’s back panel.

MIC 2

Use 1/4”

jack

V O LTA G E

 

OUTPUT

 

 

 

 

 

 

 

INPUT

 

 

 

~AC INPUT

 

 

 

 

 

 

 

 

 

 

 

FUSE F 500mA 250V

BALANCED

Master

Booth

Rec

 

CH 5

CH 4

CH 3

 

 

CH 2

 

CH 1

 

 

L

 

 

L

L

 

 

L

L

L

L

GND

R

L

 

 

 

 

MIC 2

R

R

R

 

 

 

 

 

 

 

 

 

 

 

R

R

 

 

 

 

R

 

 

 

R

NPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line

9

Line

8

Line

7

Line

6

Line

5

Phono

2

LN 4

PH 2

Line

3

Phono

1

LN 2

PH 1

Line

1

 

CH 2

 

 

 

 

 

 

 

 

 

 

 

 

/Line

4

 

 

 

 

/Line

2

 

 

 

 

 

Magnetic cartridge turntable

L

L

LEFT output

 

 

 

R

R

RIGHT output

PH 2 Line 3

Phono 1 LN 2

 

 

 

/Line 2

GROUND wire from turntable

NOTE!

CH

L

R

PH 1 Line 1

 

 

V O LTA G E

 

OUTPUT

 

 

 

 

 

 

 

INPUT

 

 

 

 

~AC INPUT

 

 

 

 

 

 

 

 

 

 

 

 

FUSE

F 500mA

250V

BALANCED

Master

Booth

Rec

 

CH 5

CH 4

CH 3

 

 

CH 2

 

CH 1

 

 

 

 

L

 

 

L

L

 

 

L

L

L

L

GND

 

 

R

L

 

 

 

 

MIC 2

R

R

R

 

 

 

 

 

R

R

R

R

 

 

Line 9

Line 8

Line 7

Line 6

Line 5 Phono

2

LN 4

PH 2 Line 3 Phono

1 LN 2

PH 1 Line 1

 

 

 

 

 

 

/Line

4

 

/Line

2

 

2 – Pyle Pro Mixer Owner’s Manual

If you use a Turntable in the Phono1/Line2 (and/or Phono2/Line4) input jack(s), be sure to place the Input Select switch in the PHONO1 (and/or PHONO2) position(s)!

Pyle Pro Mixer Owner’s Manual – 3

Image 3
Contents PYD2200 SpecificationsInput/Output Features Features and Controls PYD2200 MixerYour Pyle PRO Series Performance Mixer Connecting Microphones Presetting the Controls Before UseConnecting the Mixer Inputs Connecting High Level Output Audio SourcesOutput to an Amplifier Using the Channel Input Gain ControlsConnecting the Mixer Outputs Using Headphones Booth OutputUsing the Mixer Controls Using the MicrophoneUsing the Crossfader with the Assign Switches Troubleshooting