Behringer Ultra-Di Pro (8-channel Direct Injection box), DI800

ULTRA-DI PRO DI800

1.1 Before you get started

1.1.1 Shipment

Your ULTRA-DI PRO was carefully packed at the assembly plant to assure secure transport. Should the condition of the cardboard box suggest that damage may have taken place, please inspect the unit immediately and look for physical indications of damage.

+Damaged units should NEVER be sent directly to us. Please inform the dealer from whom you acquired the unit immediately as well as the transportation company from which you took delivery of the unit. Otherwise, all claims for replacement/repair may be rendered invalid.

+To assure optimal protection of your ULTRA-DI PRO during use or transport, we recommend utilizing a carrying case.

+Please always use the original packaging to avoid damage due to storage or shipping.

+Never let unsupervised children play with the ULTRA-DI PRO or with its packaging.

+Please dispose of all packaging materials in an environmentally-friendly fashion.

1.1.2 Initial operation

Please make sure the unit is provided with sufficient ventilation, and never place the ULTRA-DI PRO on top of an amplifier or in the vicinity of a heater to avoid the risk of overheating.

+Before plugging the unit into a power socket, please make sure you have selected the correct voltage:

The fuse compartment near the power plug socket contains three triangular markings. Two of these triangles are opposite one another. The voltage indicated adjacent to these markings is the voltage to which your unit has been set up, and can be altered by rotating the fuse compartment by 180°. ATTENTION: This does not apply to export models that were for example manufactured only for use with 120 V!

+If you alter the unit’s voltage, you must change the fuse accordingly. The correct value of the fuse needed can be found in the chapter

“SPECIFICATIONS”.

+Faulty fuses must be replaced with fuses of appropriate rating without exception! The correct value of the fuses needed can be found in the chapter “SPECIFICATIONS”.

Power is delivered via the cable enclosed with the unit. All required safety precautions have been adhered to.

+Please make sure that the unit is grounded at all times. For your own protection, you should never tamper with the grounding of the cable or the unit itself. The unit shall always be connected to a mains socket outlet with a protective earthing connection.

1.1.3 Warranty

Please take a few minutes and send us the completely filled out warranty card within 14 days of the date of purchase. You may also register online at www.behringer.com. The serial number needed for the registration is located at the top of the unit. Failure to register your product may void future warranty claims.

2. CONTROL ELEMENTS

The BEHRINGER ULTRA-DI PRO features eight identically built channels. The control elements described here refer therefore to all channels.

The INPUT connector is used for connecting unbalanced as well as balanced signal sources.

Because both INPUT and LINK connectors are wired in parallel, the LINK TRS connector can be used both as an input and as a direct unbalanced output of the INPUT signal. For the latter, you can for example connect LINK with the input of a monitor amplifier.

The unbalanced input signal can be tapped into at the UNBAL OUT TRS connector – after passing through the

amplification circuitry (see and ). Essentially, the signal is identical to the signal located at the XLR output in the back; the only difference is that it is unbalanced and

has therefore no Ground Lift functionality (see ).

Fig. 2.1: Front panel control elements

The -30 dB attenuation switch increases the operating range of the DI800 considerably, from low signal levels of a high-impedance mic or a guitar, all the way to speaker connectors of a guitar amplifier.

+Use the -30 dB switch only when the DI800 starts distorting (and not the mic preamp). When this is not the case, avoid using this function, since the lowest amount of attenuation is desirable in order to obtain the lowest signal-to-noise ratio possible.

Using the GND LIFT switch, you can fully separate input and output grounding. Depending on how the equipment to which your DI800 is connected is grounded, using the GND LIFT switch lets you lower hum noise or ground loops. When the GND LIFT switch is depressed, the ground connection is interrupted (the LED is lit red). When the switch is in the PHANTOM OR MAINS POWER ON setting, the LED is lit green (when the GND LIFT switch is not pressed).

The +20 dB switch increases the input signal level by 20 dB.

Use the POWER switch to power up your DI800. The POWER switch should always be in the “Off” position when you are about to connect your unit to the mains.

+To disconnect the unit from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible. If mounting in a rack, ensure that the mains can be easily disconnected by a plug or by an all-pole disconnect switch on or near the rack.

2. CONTROL ELEMENTS

Ultra-Di Pro (8-channel Direct Injection box), DI800 specifications

The Behringer DI800 Ultra-DI Pro is a sophisticated 8-channel direct injection box designed to facilitate seamless integration between instruments and sound systems. Whether in a studio or live performance setting, the DI800 offers crucial versatility and effective signal management for musicians and audio engineers alike.

One of the standout features of the DI800 is its ability to handle multiple signals simultaneously, making it ideal for band setups or recording situations where several instruments are in play. The box is equipped with eight high-quality transformer-isolated direct channels, which provide impeccable audio fidelity while eliminating unwanted noise and interference. This ensures that the sound captured is pure and free from the issues commonly associated with ground loops.

The DI800 leverages advanced technology such as balanced XLR outputs, which support long cable runs without sacrificing sound quality. Each channel features a switchable input that can accommodate both active and passive instruments, enhancing its adaptability. This means whether you are working with electric guitars, keyboards, or even high-impedance pickups, the DI800 can effectively accommodate all without the need for multiple devices.

Additional features include individual ground lift switches on each channel, providing the flexibility to eliminate any hum or buzz that may occur in certain environments. A built-in 48V phantom power supply allows for the use of condenser microphones, making the DI800 even more versatile for various recording applications.

The compact design of the DI800 offers ease of portability, crucial for touring musicians and mobile sound engineers. Its rugged metal chassis ensures durability and reliability, standing up to the rigors of stage life. Furthermore, the unit has a user-friendly interface with clear labeling and intuitive controls, allowing for quick adjustments during performances or sessions.

In conclusion, the Behringer DI800 Ultra-DI Pro is an essential tool for anyone looking to achieve professional-quality sound. With eight channels, transformer isolation technology, versatile connectivity options, and robust build quality, it is a choice that caters to both studio and performance needs. This direct injection box empowers users to deliver their best audio experience while minimizing technical headaches.