Nady Systems Wireless Guitar Kit owner manual WGA 15 Wireless Guitar Amp Operation, Specifications

Page 7

WGA - 15 Wireless Guitar Amp Operation

(21)

Back of WGA-15

(15) (14) (13)

(16)

(17)

(18)

(19)

(20)

(12)

(11)

Front Panel

(11)POWER SWITCH — Turns on power to the amplifier. Make sure unit is plugged into AC and the Level control is turned down before turning on the amp.

(12)POWER LED — Lights red to indicate the power is on.

(13)TX LED — Lights green to indicate the guitar transmitter is on, within range, and the RF signal is being being re- ceived.

(14)AUDIO LED — Lights amber to indicate audio is present.

(15)PHONE JACK — This jack should be used for headphones. When plugging into this jack, the internal speaker is disabled.

Note: This jack is meant to receive a stereo headphone 1⁄4” TRS plug. Do not plug a mono 1⁄4” TS plug into this jack

(16)INPUT JACK — Use this jack to plug in the guitar cord when not in wireless operation. Plugging into this jack will automatically disable the wireless receiver capability.

(17)GAIN CONTROL — This control adjusts the input gain of the guitar audio. Turn this control to minimum for clean sounding guitar. Turn it to maximum for heavy distortion. Blues style distortion can be achieved by setting this control to mid.

(18)LEVEL CONTROL — This control adjusts the final master volume of the audio.

(19)TREBLE CONTROL — This control adjusts the treble frequencies (approx 5K Hz) to increase high cut, presence, and add definition to your sound.

(20)BASS CONTROL — This control adjusts the bass frequencies (approx 120 Hz) for warmer sound and stronger low

end.

(21)ANTENNA — The antenna wire is dressed inside the amp cabinet. Do not remove or reposition this wire.

Specifications

Built-In Wireless System

RF Transmission Frequency: 171.90MHz (Ch A)

Frequency Response: 40-20,000 Hz, +/-3dB

Dynamic Range: 100dB

Total Harmonic Distortion: <0.65%

Operating Range: up to 200+ ft. line-of-sight

Transmitter Batteries: Two 9V alkaline, 26mA drain, up to 30 hours battery life

Controls and Indicators:

Lightning Guitar (transmitter): Transmitter ON/OFF rocker switch with integrated LED “ON” indicator (LED dims below 6.9V indicating need for battery change). Transmitter not op- erational if cord is plugged into guitar OUTPUT jack WGA-15 (receiver): Amp power/Receiver ON/OFF rocker switch LED indicators: Power ON, TX ON (transmitter signal received), and AUDIO ON (audio signal from guitar received)

Receiver not operational if cord is plugged into amp INPUT jack Transmitter and Receiver Antennas: Both internal to guitar and amp respectively

WGA-15 Guitar Amp

Power Output: 15 Watts RMS @ 4Ω

Speaker: 5” full-range guitar speaker

Impedance: 4Ω

Power handling: 20 Watts

Guitar Input Connector: 1/4” TS mono connector

Input Impedance: 200KΩ

Headphone Output Connector: 1/4” TRS stereo connector

Bass Control: +/- 12dB @ 120Hz

Treble Control: +/- 12dB @ 5KHz

Power Requirements: 115VAC 60Hz

Internal Fuse: 0.5A 250V

Dimensions HWL: 11.8” x 5.7” x 7.4”

Weight: 10.5 lbs

(7)

Image 7
Contents Wireless Guitar Kit N t e n t s Guitar Kit ContentsLightning Guitar WGA-15 15W Wireless Guitar AmplifierT r o d u c t i o n A t u r e sThese terms for a better understanding of your instrument Lightning Guitar PartsHandling Care Learning How to Play Your Lightning GuitarCleaning and Maintenance Taking Proper Care of Your Lightning GuitarInstallling the Vibrato Arm, aka Whammy Bar Lightning Wireless Guitar OperationWGA-15 Guitar Amp WGA 15 Wireless Guitar Amp OperationSpecifications Built-In Wireless SystemService for Your Nady Audio Product