Nady Systems CMX-16A owner manual N T R O L S a N D C O N N E C T I O N S, Mono Input Section

C O N T R O L S A N D C O N N E C T I O N S

1. MONO INPUT SECTION

(1) MIC INPUT

The Mic input is an electroni- cally balanced XLR type designed to accept signals

(1) from any balanced low

		impedance (Low Z) micro-
		phone. To accommodate
		condenser microphones, this
		input is also equipped with
		+48VDC phantom power
	(2)	globally switchable to all
		XLR input jacks with the
		Phantom Power switch
		(27) in the Master Section.
		Dynamic or ribbon-type
(3)		microphones do not require
		phantom powering. It will be
		necessary to adjust the
		channel gain with the input
		Trim control (4) to achieve

a nominal operating level. The XLR jack is configured for: Pin1 = ground, Pin2 = positive (+), Pin3 = negative (-).

[Note: The Mic inputs are more sensitive than the Line inputs. Also, do not connect mics with the phantom power switched on, as indicated by the Phantom Power On LED (27A) next to the Phantom Power switch. Never use unbalanced mic cables with the Phantom Power switched on. Never short the +48VDC to ground, as that can cause serious damage to your mixer. Also, mute the Monitor/PA speakers when turning the phantom power on or off.]

(2) LINE INPUT

The Line input is designed to accept balanced or unbalanced line-level signals such as those from keyboards, drum machines, or samplers. There is enough gain available on the line input to accept even lower level signals, such as those from an unbalanced microphone or guitar output. Use the Trim control (4) to adjust for the desired level. If a balanced signal is to be connected to the line input, then a 1/4" TRS (stereo) phone plug should be wired for: Tip = positive (+), Ring = negative (-), Sleeve = ground.

(Note: Only either the Mic or the Line input of a given channel can be connected at one time. Never connect both simultane- ously to the same channel.)

(3) INSERT

Channels 1-8 are equipped with insert jacks to connect exter- nal signal processors, such as compressors, noise reduction systems, or effects devices, to the individual input channels.

Insert points are useful for adding dynamic processing or equalization to a channel or the mix. Unlike reverbs, etc., which are usually added to the dry signal, dynamic process- ing is normally applied across an entire signal. Here an Aux Send would be inappropriate. Instead the signal is intercepted somewhere along the channel, fed through the dynamics

processor and/or EQ, then returned to the console at the same point where it left. The insert point is normalized, i.e. the signal is only interrupted when a plug is plugged into it. The insert jack is located pre EQ in the channel and is config- ured as: Tip = send, Ring = return, Sleeve = ground. The Insert can also be used as a channel direct output by sending the signal from the ring. To use the Insert as a direct output, insert a 1/4" phone plug halfway into the Insert jack so the tip of the plug connects with the ring of the insert jack. The jack will click into place when the connection to the ring is made.

(4) TRIM CONTROL

The trim control adjusts the input sensitivity (channel gain) of the mic and line inputs on channels 1 through 8. This control can be adjusted to accommodate input signals from a wide variety of sources, from the high outputs from keyboards or drum machines to the small signal outputs of microphones. This wide range eliminates the need for Mic/Line switching. The best balance of S/N and dynamic range will be achieved if you adjust the TRIM control on each channel separately so that the Peak Indicator LED (8) for that channel lights occa- sionally.

(5) EQUALIZER CONTROLS
All mono input channels are fit-
ted with a three-band EQ. All
three bands have up to 15 dB	(4)
of cut and boost, with a center
detent for "off". The frequency
response is flat when all three
EQ knobs are in the center
detent position. The upper and
lower shelving controls have
their frequencies fixed at 12
kHz and 80 Hz respectively.
The midrange control has a	(5)
peaking response at 2.5KHz
(Q fixed at 1 octave). The
channel EQ is an important
part of the mixer as it allows
the user to control the tonal
characteristics of each instru-
ment separately. For example,
boosting the LOW can fatten
the sound and add punch to
the bass or drums; the MID
control can be used to define	(6)
the midrange or bring out the

vocals; and adjusting the HIGH control can provide a crisp sounding high end. A very important, yet often overlooked technique is to use the EQ to

subtract from the mix. Cutting the HIGH control can reduce unwanted hiss during multi-track recording, while attenuating the MID or LOW can eliminate feedback in a live performance or clear up a muddy sounding mix.

6