Using the Microphone Shock Mount, Service

USING THE MICROPHONE SHOCK MOUNT

The SSM-3 spider shock mount is available as an option for the SCM 1000. It uses an elastic suspension to isolate the Microphone from vibration, thereby lowering noise transmitted to the microphone from the stand. This is a useful tool in many situations, such as when the performer is tapping his or her feet, or when there is noise pickup from the rumbling of traffic outside of the building. The disadvantage of using the shock mount is that the weight of the microphone may make it drift in the elastic suspension, so mic placement may take a little longer.

To insert the SCM 1000 into the SSM-3 shock mount, pinch close the levers on the sides of the mount to the open position, then slide the microphone into place.

USING THE FOAM WINDSCREEN

The FW-1 foam windscreen is available as an option for the SCM 1000. This windscreen fits over the grill portion of the micro- phone and is designed primarily to decrease bass rumble (from wind noise pickup) during outdoor live or

recording use. It is also useful in keeping mouth spray out of the microphone head. The FW-1 or other windscreen should be used whenever someone is close miked to both protect the microphone and to also eliminate "popping" sounds from percussive breath sounds.

(Note: Be aware that the foam windscreen will slightly attenuate the high frequency response of the microphone.)

CONNECTING THE SCM 1000

The SCM 1000 can be used in live sound reinforcement and broadcasting and in studio or live recording. It must be powered by 48V phantom power (such as supplied by the optional Nady SMPS-1 phantom power supply or a mixing console with phantom powering), and amplified by a microphone pre-amp (such as built into a mixer, or a stand-alone unit).

(Note: Make sure to set the pre-amp to the proper gain level—too much gain may distort subsequent amplifiers and too little may result in a noisy signal)

The SCM 1000 can be connected to your mixer or phantom power supply using a standard balanced 3-pin XLR microphone cable. Before connecting to a mixer directly, turn the channel to which you’re connecting to its lowest gain setting. If you are using the Nady SMPS-1 Phantom Power Supply, connect in the following order:

1.Connect the SCM 1000 to the SMPS-1

2.Connect the SMPS-1 Signal Output to your mixer

3.Connect the SMPS-1 to the AC power supply (115—230VAC)

4.Turn on the SMPS-1 Power ON/OFF switch

5.Slowly turn up the channel gain in your mixer to the desired level

SERVICE

(U.S.) Should your Nady microphone require service, please contact the Nady Service Department via phone at (510) 652- 2411 or e-mail at service@nadywireless.com

(INTERNATIONAL) For service, please contact the Nady distributor in your country through the dealer from whom you pur- chased this product.

Do not attempt to service this unit yourself as it will void your warranty

Date of purchase ___________________________________ Serial # ____________________________________________________________________________

Dealer’s Name _________________________________________________________________________________________________________________________

Street _________________________________________________________________________________________________________________________________

City ______________________________________________ State ___________________________ Zip _______________________________________________

SCM 1000 SPECIFICATIONS

Type: True condenser pressure-gradient		IEC 268-4(A weighted):	18dB-A
	microphone with 1.1 inch	S/N ratio re 1Pa:	76dB
	diaphragm and FET pre-amplifier	Power requirement:	+48VDC phantom power
Polar pattern: Selectable Cardioid, ommi-		Current consumption:	< 3mA
	directional and figure 8	Ambient temperature range:	14˚F to 140˚F(-10˚C to +60˚C)
Controls: Selectable low-cut filter and 10dB		Relative humidity range:	90%(68˚F, 20˚C), 85%(140˚F, 60˚C)
	pad	Connector:	3-pin XLR (gold plated)
Open circuit sensitivity: 10mV/Pa=-40dBV (0dBV=1V/Pa)		Phasing: Positive voltage on pin 2 relative to
	-10dB attenuation externally		pin 3
Frequency range:	selectable	Mic cable:	3-pin XLR standard cable
Frequency range:	20 to 20,000Hz		(not supplied)
Rated output impedance: < 200 Ohms		Size: Diameter: 2.1" (55mm),
Recommend load Impedance: ≥1000 Ohms			Length: 6.5" (165mm)
Max. SPL (1% THD @1000Hz): 134dB		Net weight: 15oz (430g)
Equivalent noise level to
DIN 45405(CCIR468-2): 26dB		Specifications and design subject to change without prior notice for improvement purposes

11/16/00