Installation, ARCHITECTS’ Specifications

Net Weight

7.9grams (0.28 oz), less cable and connector

Certification

Conforms to European Union directives, eligible to bear CE marking; meets European Union EMC Immu- nity Requirements (EN 50082–1: 1992).

CARTRIDGE	CONNECTOR
RED CODED TERMINAL
YELLOW
SHIELD	2	1
RED		3
BLACK

INTERNAL CONNECTIONS

FIGURE 3

INSTALLATION

Tie Clasp Assembly

Insert the SM11 in the tie clasp and anchor the cable as shown in Figure 4. Affix the clasp to a tie, shirt, or blouse. Note that the microphone can be swiveled 360° in its holder for left, right, or vertical (“pen clip”) use.

CABLE ANCHORING

FIGURE 4

Tie Tack Assembly

Remove the clutch from the tie tack assembly and insert the tie tack holder in the tie (or through the tie and shirt if de- sired). Affix the clutch to the pin of the tie tack holder. Insert the SM11 in the tie tack holder.

Connector and Belt Clip

With the SM11 installed in one of the assemblies de- scribed above, insert the connector in the connector belt clip and fasten the belt clip to the user’s belt, waistband or other

clothing. Excess microphone cable can be inserted in the user’s pocket or tucked into the waistband.

ARCHITECTS’ SPECIFICATIONS

The microphone shall be a moving–coil (dynamic) type with a frequency response of 50 to 15,000 Hz. The micro- phone shall have an omnidirectional polar characteristic. The microphone shall be low impedance with a rated imped- ance of 150 ohms for connection to microphone inputs rated at 19 to 300 ohms. The microphone output shall be –64 dB where 0 dB = 1 milliwatt per 10 microbars.

The microphone shall be a lavalier type, and shall be pro- vided with a 1.2m (48 in.) non–detachable, two–conductor, shielded cable with a professional, three–pin audio connec- tor designed to mate with Cannon XL series, Switchcraft A3 (Q.G.) series or equivalent connectors. The microphone shall also be provided with a tie clasp assembly, tie tack as- sembly, connector belt clip, and carrying/storage bag.

The overall dimensions of the microphone shall be 33.5

mm(1 – 5/16 in.) in length and 14.7 mm (9/16 in.) in diame-

ter.

The microphone shall be the Shure Model SM11 or equivalent.

ACCESSORIES AND REPLACEMENT PARTS

The following furnished accessories and replacement parts can be ordered through your Authorized Shure Profes- sional Products Dealer or from Shure Incorporated.

Tie Clasp Assembly . . . . . . . . . . . . . . . . . . . . . . . RK203TC

Tie Tack Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 90A2384

Connector Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . RK200BC

Carrying/Storage Bag . . . . . . . . . . . . . . . . . . . . . . . . . 26A13

Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R99

Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C91

Instrument Mounting Kit . . . . . . . . . . . . . . . . . . . . . . . RK279

For additional service or parts information, please con- tact Shure’s Service Department at 1–800–516–2525. Out- side the United States, please contact your authorized Shure Service Center.

SHURE Incorporated Web Address: http://www.shure.com 222 Hartrey Avenue, Evanston, IL 60202–3696, U.S.A. Phone: 847-866–2200 Fax: 847-866-2279

In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414

In Asia, Phone: 852-2893-4290 Fax: 852-2893-4055

Elsewhere, Phone: 847-866–2200 Fax: 847-866-2585